SharkBite 24687 1/2" Straight ...
IN STOCK (leaves warehouse same day if ordered before 3pm ET)
$20.82
SharkBite 24687 1/2" Straight Stop x Click Seal® Faucet Connector, 30"

SharkBite 24687 1/2" Straight Stop x Click Seal® Faucet Connector, 30"

(No reviews yet) Write a Review

Model: 24687

In Stock (leaves warehouse same day if ordered before 3pm ET)

$20.82
Adding to cart… The item has been added
Free Shipping on orders over $199
We price match and offer bulk discounts! Click Add to Quote. It's quick and easy.
✨
Earn points with this purchase! You can redeem points for giftcards, iPads, XBox's and more. View Rewards
Free Keying on all locks
You may also like

SharkBite 24687 1/2" Straight Stop x Click Seal® Faucet Connector, 30"

The SharkBite 24687 is a one-piece supply stop and faucet connector assembly built for fast rough-in and repair work under sinks and behind fixtures. It combines a 1/2 in. push-to-connect straight stop valve with a flexible 30 in. hose terminating in a 1/2 in. NPSM Click Seal® faucet connector. The push-to-connect end accepts PEX, copper, CPVC, PE-RT and HDPE pipe in any combination, so a plumber can transition between pipe materials without adapters, unions, or additional fittings. This connector is designed for behind-the-wall and under-fixture installation, not as a finished decorative supply line.

Key Features

  • Trade Size: 1/2 in. push-to-connect stop valve paired with a 1/2 in. NPSM Click Seal® faucet connector end, joined by a 30 in. flexible hose.
  • One-Piece Integrated Design: the stop valve, hose, and faucet connector are combined into a single assembly for faster installation with fewer connection points to check.
  • Push-to-Connect Stop Valve: no special tools, crimping, glue, or soldering required to make the pipe-side connection, and the fitting can be rotated for easier positioning in tight spaces.
  • Click Seal® Faucet Connector: the nut is hand-tightened and produces an audible click when a secure, watertight connection is made, which helps prevent over-tightening at the fixture.
  • Broad Pipe Compatibility: works with PEX, copper, CPVC, PE-RT, and HDPE pipe in any combination on the push-to-connect end.
  • Wet-Line Rated: can be installed in wet lines, which reduces downtime on repair and replacement jobs where shutting down the whole system isn't practical.
  • Removable Connection: the push-to-connect end can be removed later using a disconnect clip or disconnect tongs, both sold separately.

Technical Specifications

  • Stop Valve Connection: 1/2 in. push-to-connect
  • Faucet Connector Thread: 1/2 in. NPSM Click Seal®
  • Hose Length: 30 in.
  • Packaging: 6 ea per pack
  • Compatible Pipe Materials: PEX, copper, CPVC, PE-RT, HDPE

Typical Applications

  • Under-Sink and Fixture Supply Stop Installation
  • Faucet and Fixture Replacement in Occupied Homes
  • Residential and Light Commercial Rough-In Plumbing
  • Repair and Retrofit Work in Tight Cabinet Spaces
  • Wet-Line Repairs Where System Shutdown Is Impractical

Why SharkBite?

SharkBite's push-to-connect technology and Click Seal® faucet connector give plumbers a single, integrated part that replaces multiple separate fittings, cutting installation errors and time on the job. The audible click confirmation on the faucet end and tool-free connection on the stop-valve end are built for professionals who need a dependable, watertight connection in tight, hard-to-reach spaces without soldering or gluing.

Manufacturer Resources

Spec Sheet

Product Specs

list_batch:
SHK-20260923
Product Type:
Supply Stop
Connection Type:
Push-to-Connect
Department:
Plumbing
Product Subgroup:
Fittings and Valves
Product Material:
Brass
Product Size:
1/2"
Product Group:
Fitting

SharkBite 24687 – Frequently Asked Questions

1) Will the SharkBite 24687 stop valve connect to copper and PEX, or do I need an adapter?
The push-to-connect end on the 24687 takes PEX, copper, CPVC, PE-RT and HDPE in any combination, so no adapter, union, or extra fitting is needed to transition between pipe materials. It is sized for 1/2 inch pipe. No crimping, glue, or solder on that end, and the fitting rotates so you can line it up in a tight cabinet.
2) What thread does the faucet end of the SharkBite 24687 have, and will it fit a standard faucet tailpiece?
The faucet end is a 1/2 inch NPSM Click Seal connector, which is the standard faucet-supply thread on a 1/2 inch tailpiece. The nut is hand-tightened only, and it clicks when the seal is made, so no wrench and no over-tightening the plastic on the faucet.
3) How long is the supply hose on the SharkBite 24687, and is that enough to reach from the stop up to a faucet?
The flexible hose is 30 inches between the stop valve and the faucet connector, which covers most standard under-sink runs from the wall or floor stop up to a lavatory or kitchen faucet tailpiece. Because the valve and hose are one piece, there is no separate supply line to buy or an extra joint to leak at.
4) Is the SharkBite 24687 a straight stop or an angle stop?
It is a straight stop, meaning the inlet and the valve are in line. Use it where the supply pipe comes out of the floor or out of the cabinet deck in line with the fixture; for a pipe stubbed out of the wall turning up to a faucet, an angle stop is the right pattern instead.
5) Can I install the SharkBite 24687 without draining the water line first?
It is wet-line rated, so it can go on a line that still has water in it. That matters on occupied-building repairs where you cannot shut down and drain the whole system to swap a faucet or a stop.
6) Is the SharkBite 24687 push-to-connect stop removable if I need to redo the connection?
Yes, the push-to-connect end comes back off with a SharkBite disconnect clip or disconnect tongs. Neither tool is included with the 24687, so order one separately if you want the option to pull the fitting later.
7) Is the SharkBite 24687 a decorative exposed supply line for a finished bathroom?
No. The 24687 is built for behind-the-wall and under-fixture work, not as a finished decorative supply. If the stop and riser will be visible in a finished space, use a chrome or brushed decorative supply kit instead.
8) Does the SharkBite 24687 come individually or in a multi-pack?
It is packaged 6 each per pack, which suits property maintenance crews and rough-in work where you are setting several fixtures at once rather than buying a single repair part.
9) What is the SharkBite 24687 valve body made of?
Brass. That is the usual body material for a commercial-duty supply stop, and it holds up better than plastic-bodied stops under repeated shutoff cycles in a rental or multi-family unit.
10) What is the SharkBite part number for the 1/2 inch straight stop with a 30 inch faucet connector?
SharkBite model 24687. It pairs a 1/2 inch push-to-connect straight stop with a 30 inch hose and a 1/2 inch NPSM Click Seal faucet connector in one assembly.
How fast can I get the SharkBite 24687 delivered?
Most orders ship the same day from our distribution partners, with quick delivery throughout the continental U.S. Need it urgently? Contact Us for expedited shipping options.
Can I return it if it doesn’t work for me?
Yes—ZenSupply offers a hassle-free return policy. If the product isn’t the right fit, reach out to our support team for a return authorization or setup a return by following our return instructions.
Does the SharkBite 24687 come with a warranty?
Absolutely. The SharkBite 24687 is backed by a manufacturer’s warranty. For full warranty terms, check the product documentation or Contact Us.
How do I get technical support or installation help for the SharkBite 24687?
You can call, text, or email our expert support team for fast answers. We’re here to help with product selection, installation tips, and troubleshooting. Contact Us
Why buy the SharkBite 24687 from ZenSupply?
ZenSupply makes it easy to get the commercial door hardware you need—fast shipping, expert support, and rewards on every order. Our team is always ready to help you choose the right product for your project.
!