Tell DB3062 - Grade 3 Double Cylinder Deadbolt

Both. The DB3062 covers a 1-3/8 to 1-3/4 inch door thickness range, so it works on older interior and residential doors as well as standard 1-3/4 inch exterior doors without a spacer kit.

No. The latch is adjustable between the two standard backsets, 2-3/8 and 2-3/4 inches, so it drops into either cross-bore location. That is the main reason it works well as a fleet replacement bolt when you don't know what's in each door.

The DB3062 ships with a 1-1/8 x 2-3/4 inch standard strike, which is the common residential deadbolt strike size, so in most cases it drops into the existing frame cutout. Face prep is a 1 x 2-1/4 inch square corner faceplate with a 1 inch housing diameter, so the bore must be a 1 inch cross bore.

Correct, the DB3062 is keyed on both the inside and the outside, no thumbturn. That's how you stop someone reaching through a glass light and turning the bolt. But many jurisdictions restrict double cylinder bolts on required egress doors, because occupants need a key to get out. Check your local code for the occupancy before specifying it. If you need a key outside and free egress inside, a cylinder x thumbturn bolt is what you want instead.

The DB3062 uses a Schlage C (SC1) keyway with a conventional cylinder, so it takes SC1 blanks and can be pinned to an existing Schlage C system. Order keyed alike if you want several openings on one key, keyed different if each unit gets its own, and there's a key code field if you're matching an existing bitting. A less-cylinder option is also available if your locksmith is supplying the cylinders.

The DB3062 is Grade 3 and classified residential, which puts it in multi-family units, interior suite doors, and light-traffic openings. For a main commercial entrance or a school, step up in grade. ZenSupply carries the Design Hardware D1 Series as a Grade 1 double cylinder bolt and the Delaney LU Series as a Grade 2 double cylinder, both same function.

The Tell DB3062 is a Grade 3 double cylinder deadbolt with an adjustable 2-3/8 to 2-3/4 backset and a 1-3/8 to 1-3/4 inch door thickness range. The closest peer at the same grade and function is the Callan 210S, a Grade 3 double cylinder deadbolt. The Deltana 7312KA2 is also a Grade 3 double cylinder deadbolt and covers a 1-3/8 to 2 inch door thickness range, so it reaches thicker doors.

The Tell DB3062 is a Grade 3 deadbolt classified for residential use. For a heavier commercial opening, the Design Hardware D1 Series double cylinder deadbolt is Grade 1 extra heavy duty for 1-3/4 inch doors, and the Dexter DB1000 double cylinder is Grade 1 for 1-3/8 to 1-7/8 inch doors. In the middle, the Dexter DB2000 double cylinder is Grade 2 over the same 1-3/8 to 1-3/4 inch door range the DB3062 covers.

The Tell DB3062 is keyed on both sides. Where a thumbturn is required inside, comparable Grade 3 single cylinder deadbolts include the Cal-Royal ED500 with adjustable backset and the Cal-Royal LSD with an ADA ergonomic thumbturn, both cylinder x thumbturn over a 1-3/8 to 1-3/4 inch door range, and the Callan 200S in Grade 3. The Hager 3115 is a Grade 2 cylinder x thumbturn deadbolt that also uses the Schlage C keyway, matching the DB3062 keyway.

A few items sit close in the deadbolt family but will not swap in. The Baldwin Reserve 8BR0618001 is a deadbolt spacer, not a lock, and the BEST 8T is a T Series tubular deadbolt tube component rather than a complete deadbolt. The Arrow 460 is a mortise lock strike. The Emtek 2050 and 2051 are European mortise deadbolts with an integrated roller latch, which need a mortise pocket, while the Tell DB3062 is a bored deadbolt with a 1 inch housing diameter. The Arrow E60 exit deadlock is non-keyed, blank plate by thumbturn, so it gives no key access at all.

If code or the tenant rules out a key on the inside, skip the double cylinder and go single cylinder. The Cal-Royal ED500 is a Grade 3 cylinder x thumbturn with adjustable backset and the same 1-3/8 to 1-3/4 inch door range as the DB3062, and the Cal-Royal LSD adds an ADA ergonomic thumbturn for openings where turning a small knob is a problem.

Yes. Keying is a required selection and one of the choices is less cylinder, which gets you the bolt and trim without cylinders. Note it takes conventional cylinders, not small format interchangeable cores, so if your system is SFIC you want a bolt prepped for it instead, such as the Arrow E61 in SFIC prep less core.

The Tell DB3062 uses the Schlage C keyway with a conventional cylinder. Peers on the same keyway include the Hager 3214 double cylinder Grade 2, the Hager 3215 single cylinder Grade 2 with a 1 inch throw, the Hager 3115 Grade 2 cylinder x thumbturn, and the Hager 3118 Grade 1 classroom deadbolt with a 6-pin cylinder. The Dormakaba D900 small case mortise deadbolt is also supplied keyed different with SC keyways, though it is a mortise case rather than a bored deadbolt.

Both are double cylinder deadbolts, but they are different products. The Tell DB3062 is a Grade 3 bored deadbolt with an adjustable 2-3/8 to 2-3/4 backset, a 1 inch by 2-1/4 inch square corner faceplate and a 1-1/8 inch by 2-3/4 inch strike, offered in 619 satin nickel and 630 satin stainless steel. The Baldwin Reserve double cylinder deadbolts come in contemporary round and contemporary square trim, and the Baldwin Estates 8011 is a contemporary 1-5/8 inch double cylinder deadbolt, so the trim shape and diameter differ. Confirm the existing bore and strike prep before swapping.

The Tell DB3062 uses a conventional cylinder. If your facility keys on small format interchangeable cores, the Arrow E61 is a Grade 2 single cylinder deadlock with SFIC prep supplied less core, for 1-3/8 to 1-3/4 inch doors, the same door range the DB3062 covers. The Deltana CL200LAIC is a Grade 2 single cylinder interchangeable core deadbolt with a 2-3/4 inch backset, and the Delaney LM Series is a Grade 1 single cylinder less core deadbolt in dull chrome US26D. All three are single cylinder, so they trade the inside key for a thumbturn.

The Tell DB3062 is offered in 619 satin nickel and 630 satin stainless steel, described as US32D. The Delaney LU Series double cylinder deadbolt is a Grade 2 unit in stainless steel US32D, so it lands on the same finish code at a higher grade. The Emtek 8323 Modern Disc deadbolt is also double cylinder but is a brass body with disc trim.

No. The Tell DB3062 is a double cylinder deadbolt, keyed on both faces. Classroom function deadbolts such as the Falcon D111 in Grade 1 heavy duty and the Falcon D211 in Grade 2 medium duty are cylinder by thumbturn, and the Corbin Russwin DL2211 and DL3211 Grade 1 cylindrical deadlocks are cylinder by blank plate for 1-3/4 inch doors. Those give key control on one face only, which is a different security outcome from keying both sides.

Two finishes: 619 satin nickel and 630 satin stainless steel. 630 is the brushed stainless look that matches most commercial 626/630 lever and closer hardware; 619 is the warmer brushed nickel typically paired with residential trim.