You may also like
AL SERVENTR COMP SPLICE A:6 B:6 CVR
Manufacturer Resources
Product Specs
- Connection Type:
- Compression
- Country Of Origin:
- Mexico (MX)
- Insulation Material:
- Cover acts as insulation
- Number Of Conductors:
- 2
- Product Group:
- Wire & Cable Management
- Product Type:
- Compression Splice Service Entrance
- Selling Unit Of Measure:
- each
- Standards:
- RUS Listed. Passes the Requirements of ANSI C119.4
- Type2:
- Wire or cable compression splice
- Department:
- Electrical
- Product Subgroup:
- Splices
- Product Size:
- 2 Inch
- Installation Category:
- None
Blackburn CSC64 – Frequently Asked Questions
1) What wire sizes does the Blackburn CSC64 service entrance splice take?
The CSC64 is a two-conductor compression splice sized A:6 B:6, so it joins a 6 AWG run to a 6 AWG run, one conductor in each barrel. It is not a multi-tap connector; if you need to splice two different sizes, you need a different A/B combination.
2) Do I need to tape or insulate the CSC64 splice after crimping?
No separate taping is required for insulation. The CSC64 ships with a cover, and that cover acts as the insulation over the crimped barrel.
3) Can the CSC64 be used on aluminum conductors, or copper only?
It is an aluminum-bodied service entrance splice, rated for aluminum conductor work. Blackburn's AL-designated compression connectors of this type are used on aluminum service entrance and utility runs; treat the abraded conductor with an oxide inhibitor as you normally would on aluminum.
4) Does the CSC64 meet utility connector requirements for service entrance splices?
It is RUS Listed and passes the requirements of ANSI C119.4, which is the standard utilities specify for sealed and unsealed connectors used on underground and service conductors. That is the pair of credentials most co-op and municipal utility specs ask for on a 6 AWG splice.
5) Is the CSC64 crimped or does it use setscrews?
Crimped. It is a compression splice, so it is installed with a die-type compression tool, not a hex key. There are no setscrews to torque or re-check.
6) How much room do I need in the pedestal or box for the CSC64?
Plan for a 2 inch body length plus the cover and the two conductor stubs entering each end. In a tight service entrance can or pedestal, lay it out before crimping, because a compression splice cannot be repositioned once the dies close.
7) Is the CSC64 sold individually or in a bag of multiples?
Each. One splice with its cover per unit, so order the exact count you need for the job rather than a carton quantity.
8) Where is the Blackburn CSC64 splice made?
Mexico. Useful if you are filing country-of-origin documentation on a government or institutional job.
How fast can I get the Blackburn CSC64 delivered?
Most orders ship the same day from our distribution partners, with quick delivery throughout the
continental
U.S.
Need it urgently? Contact Us for expedited shipping options.
Can I return it if it doesn’t work for me?
Yes—ZenSupply offers a hassle-free return policy. If the product isn’t the right fit,
reach out to our support team for a return authorization or setup a return by following our return instructions.
Does the Blackburn CSC64 come with a warranty?
Absolutely. The Blackburn CSC64 is backed by a manufacturer’s warranty.
For full warranty terms, check the product documentation or Contact Us.
How do I get technical support or installation help for the Blackburn CSC64?
You can call, text, or email our expert support team for fast answers. We’re here to help with
product
selection,
installation tips, and troubleshooting. Contact Us
Why buy the Blackburn CSC64 from ZenSupply?
ZenSupply makes it easy to get the commercial door hardware you need—fast shipping, expert support,
and
rewards on
every order.
Our team is always ready to help you choose the right product for your project.