You may also like
Anchors 1/4 X 1-3/4 Wedge Ancr SS (Jar 100)
Manufacturer Resources
Product Specs
- Division:
- Electrical H1
- Pack Type:
- Jar
- Product Group:
- Fasteners
- Sub Division:
- Electrical-E H2
- Department:
- Electrical
- Product Subgroup:
- Anchors
Metallics JTS11340SS – Frequently Asked Questions
1) What size drill bit do I need for the Metallics JTS11340SS wedge anchor?
Use a 1/4 inch carbide-tipped masonry bit. Wedge anchors are sized by their own diameter, and the hole matches that diameter exactly, so a 1/4 inch anchor goes into a 1/4 inch hammer-drilled hole. Drill the hole deeper than the embedment you need so dust can settle below the anchor. With a 1-3/4 inch overall length, embedment is limited, so keep your fixture material thin: whatever thickness you bolt through comes off the usable embedment.
2) Will a 1/4 x 1-3/4 wedge anchor work in hollow block or brick?
No. Wedge anchors like the JTS11340SS are for solid, poured concrete only. The expansion clip needs solid material around it to grip, and it will spin or pull out of hollow CMU, mortar joints, or brick. For hollow block use a toggle or a sleeve anchor rated for hollow base material instead.
3) Is the JTS11340SS stainless steel all the way through, and can I use it outdoors?
It's a stainless steel wedge anchor, body and expansion clip, which is why it's specified for exterior and damp locations where a plated carbon steel anchor would rust and stain the concrete. Typical uses are rooftop equipment supports, exterior strut and conduit racks, and wash-down areas. Pair it with stainless or compatible hardware to avoid galvanic issues.
4) Is 1-3/4 inches long enough for a wedge anchor, or should I go longer?
1-3/4 inches is a short wedge anchor, suited to thin fixtures, light conduit straps, strut clips, device and panel feet, and anchoring into slabs where you don't have depth to work with. Remember the anchor length has to cover the thickness of what you're fastening plus the embedment into the concrete. If you're bolting through a thick base plate or a structural bracket, step up to a longer 1/4 inch anchor rather than losing embedment.
5) How many anchors come in a jar of the Metallics JTS11340SS?
100 anchors per jar, packaged in Metallics' jar pack. Nuts and washers are included on wedge anchors of this style, so each anchor is ready to set. For a conduit or strut install where you're shooting one anchor per clamp or support, a jar covers a good run of a job without reordering.
6) What's the exact part number to reorder the 1/4 x 1-3/4 stainless wedge anchor from Metallics?
Metallics part number JTS11340SS, a 1/4 x 1-3/4 inch stainless steel wedge anchor supplied 100 to a jar. That's the number to quote for a reorder or to match an existing spec line.
How fast can I get the Metallics JTS11340SS delivered?
Most orders ship the same day from our distribution partners, with quick delivery throughout the
continental
U.S.
Need it urgently? Contact Us for expedited shipping options.
Can I return it if it doesn’t work for me?
Yes—ZenSupply offers a hassle-free return policy. If the product isn’t the right fit,
reach out to our support team for a return authorization or setup a return by following our return instructions.
Does the Metallics JTS11340SS come with a warranty?
Absolutely. The Metallics JTS11340SS is backed by a manufacturer’s warranty.
For full warranty terms, check the product documentation or Contact Us.
How do I get technical support or installation help for the Metallics JTS11340SS?
You can call, text, or email our expert support team for fast answers. We’re here to help with
product
selection,
installation tips, and troubleshooting. Contact Us
Why buy the Metallics JTS11340SS from ZenSupply?
ZenSupply makes it easy to get the commercial door hardware you need—fast shipping, expert support,
and
rewards on
every order.
Our team is always ready to help you choose the right product for your project.