Delaney 1000 Series - 8 Foot Standard Sliding Barn Door Hardware Kit

The brackets project 2-1/2 inches from the wall, and that projection is what decides whether the door clears door casing, baseboard, or a light switch. Measure the thickest trim in the door's travel path: if it stands out more than about 2-1/2 inches minus your door thickness allowance, you'll need to shim the track out. Brackets are 13 inches long and 2-1/2 inches wide.

The kit is complete for the hardware side: two hangers with bearing wheels, one 8 foot track, standoffs and lag bolts, two door stops, and all the bolts, nuts and washers. What it does not include is the door itself, a floor guide, or any pull or latch, so plan on sourcing those separately along with a header board if your framing doesn't line up with the standoff spacing.

No, and it is the substitution that catches people most often. The Delaney 1000 Series 8 foot kit is a standard exposed system: the hangers with bearing wheels mount to the door face and ride on the outside of the track, and the track stands off the wall on standoffs and lag bolts with a 2-1/2 inch bracket projection and 13 inch brackets. Concealed systems such as the Emtek B13030 flat track and the Pemko LP200A6 hide the wheel inside the track profile, so the door prep, the mounting pattern and the wall standoff geometry are different. Changing between the two means re-drilling the door and re-laying out the header anchors, not just swapping a track. If the existing hardware is a Delaney 1000 Series and you only need to replace the track, stay within the same standard exposed configuration.

Both are steel sliding door hardware sets, but they present differently on the wall. The Delaney 1000 Series 8 foot kit is a standard exposed-hanger design: a 96 inch track with two hangers riding on bearing wheels, standoffs and lag bolts, two door stops, and the bolts, nuts and washers needed to hang the door, rated for doors up to 400 pounds and door thicknesses of 1-3/8 inch to 1-3/4 inch. The Emtek B13030 is a flat track set built around a low profile concealed wheel, so the roller sits hidden behind the track face rather than showing as a visible wheel above the door. If a property manager wants the hanger hardware to read as part of the look, the Delaney exposed-wheel kit does that; if the design calls for the wheel out of sight, the Emtek flat track is the concealed-wheel approach.

No. The Pemko LP200A6 is a 72 inch low profile concealed sliding door track system with a 200 pound capacity, so a 400 pound door is double what that system carries no matter how the opening measures. The Delaney 1000 Series 8 foot kit accommodates doors up to 400 pounds on a 96 inch track. On a barn door install the track also has to run roughly twice the door width so the door can clear the opening when open, which is why a 6 foot opening usually still calls for an 8 foot track. For a heavy solid core slab, the 1000 Series 8 foot kit is the one sized for the load; the Pemko LP200A6 suits lighter doors where the concealed low profile track is the point.

Center-to-center is 3-1/2 inches. That's the figure to use when you're laying out the through-bolt holes on the door face, and it's worth checking against an existing door if you're swapping hangers onto a slab that's already drilled.

Delaney lists the 1000 Series as residential. For a home office, pantry, or bedroom door it's the right class of hardware. For a high-traffic commercial corridor or an opening where a sliding door has to hold up to constant public use, spec a commercial-rated sliding system instead.

The Delaney 1000 Series 8 foot set is a complete hardware kit for a single door: two hangers with bearing wheels, one 8 foot track, standoffs and lag bolts, two door stops, and all required bolts, nuts and washers, in a steel build and offered in US32D satin stainless steel, US15 satin nickel, US19 black and US10B oil rubbed bronze. The Pemko LP200A6 is described as a track system, so a contractor pricing a job from it should confirm the hanger and stop components separately. If you want one line item that hangs the door start to finish on a residential opening, the 1000 Series 8 foot kit is the complete-kit option.

Four: US32D satin stainless steel, US15 satin nickel, US19 black, and US10B oil rubbed bronze. For a property manager matching several units, US19 black is the one that reads as the standard modern barn door look, while US15 and US10B are the ones that tie into existing lever and hinge finishes on the rest of the openings.