Deltana MP9116 Modern Cabinet Angle Pull 9-1/16", Aluminum

The MP9116 mounts with a concealed screw installation, so the screws come through the back of the door or drawer front and there is no visible hardware on the face. What the data does not fix for you is hole spacing, so measure the pull's screw centers against your existing holes before drilling anything. Overall length is 9-1/16 inches, which gives you a long footprint on a drawer front or a tall appliance panel.

Projection is 1-9/16 inches. That is the clearance you need between the pull and anything beside it, a wall return, an adjacent appliance, or a door swinging past. On a galley run where two cabinet doors meet at a corner, check that 1-9/16 inches of stand-off does not put a knuckle into the neighbouring door when it opens.

At 9-1/16 inches overall it is in appliance-pull territory by length, but Deltana lists the Modern Angle Pull as residential aluminum hardware, not an appliance-rated pull. A refrigerator door pulled open hundreds of times a week loads the pull hard. If it is a true appliance panel, the Schaub 79-8 Steamworks 8 inch pull is catalogued specifically as an appliance pull.

The Deltana MP9116 Modern Cabinet Angle Pull is aluminum. If the job calls for a forged solid brass pull in a modern profile, the Omnia 1968/102 Modern Cabinet Pull is forged solid brass with 4 inch center-to-center spacing, and the Omnia 1970 Modern Cabinet Pull is forged solid brass with a 1-1/4 inch projection. The MP9116 projects 1-9/16 inches, so the Omnia 1970 sits closer to the door face; check drawer-front clearance and the existing bore spacing before swapping.

The Deltana MP9116 angle pull projects 1-9/16 inches from the face of the door or drawer. Among modern brass pulls, the Omnia 1969 and the Omnia 1971 both list a 1-3/16 inch projection, and the Omnia 1970 lists 1-1/4 inches. In a galley kitchen or a tight corridor of casework where a hand or a hip catches the hardware, that difference in stand-off is the number to work from.

The Deltana MP9116 measures 9-1/16 inches. For shorter runs, the Trimco 553 Series drawer pull is 3 inch center-to-center, and the Trimco 562 Series comes in 3-1/2 inch, 4 inch, and 96mm center-to-center. The Omnia 1968/102 is 4 inch center-to-center. Note that center-to-center is the bore spacing, not the overall length, so measure the existing holes rather than the old pull end to end.

Aluminum, both the material and the substrate. It is lighter than a forged brass pull and Deltana lists the Modern Angle Pull line as residential. For a landlord standardizing on kitchens and vanities across units, that is a fine fit. For a high-traffic commercial millwork run where a pull gets yanked all day, a forged solid brass option like the Omnia 1969 or 1970 Modern Cabinet Pull is the heavier-material route.

Three finishes: Oil Rubbed Bronze, Brushed Nickel, and Polished Chrome. That is the complete range on the MP9116, so if your other openings are satin brass or matte black, this pull will not match and you want a different line. The Modern Angle Pull is also made in three lengths, so you can carry one finish across drawer banks and door fronts of different widths.

An angle pull has a squared, L-shaped return into the door rather than a round bar on posts, which reads flatter against a slab front and gives you a straight edge to hook fingers over. If you want the round-bar look instead, the Emtek Bar Cabinet Pull from the Schaub collection is that type. For a drawer front where you want no projection at all, an edge pull such as the Schaub 10011 Sabre in 4 inch center-to-center mounts at the top edge instead of the face.

The Deltana Modern Angle Pull is made in three lengths. The MP9116 is the 9-1/16 inch one, which suits wide drawer fronts. For narrower doors you want one of the shorter lengths in the same line, ordered under its own model number, and you can keep the same finish across all of them so a kitchen reads as one set.

No. The Deltana MP9116 is a surface-mounted angle pull with a 1-9/16 inch projection, mounted on the face of the door or drawer. The Schaub 10010, 10011, and 10012 Sabre pulls are edge pulls, in 3 inch, 4 inch, and 5 inch center-to-center, and they mount at the edge of the panel rather than on its face. They serve sliding panels and flush-front casework where nothing may stand proud of the face. The two are not interchangeable in the same bore pattern.

The Deltana MP9116 is classified for residential use as a cabinet pull. For a panel-ready appliance door, the Schaub 79-8 Steamworks 8 inch pull is built as an appliance pull, which is the grip made for the weight and the pulling force of an appliance door rather than a drawer front. Where the kitchen carries both, contractors commonly run the cabinet pull on the casework and the appliance pull on the fridge and range panels.

On a narrow drawer or a single cabinet door, a knob replaces a 9-1/16 inch pull with one bore instead of two. The Orca Hardware CK-15030 Bachelor Collection round cabinet knob is 1-1/4 inch diameter, the CK-16030 is a round ring knob at the same 1-1/4 inch diameter, and the CK-17025 Blackcomb Collection knob is square at 25mm. All three are cabinet knobs, so they will not reuse the two-hole layout the MP9116 is drilled for.

They are both surface pulls but they are different parts. The Deltana MP9116 is an aluminum angle pull with a 1-9/16 inch projection, finished in Oil Rubbed Bronze, Brushed Nickel, or Polished Chrome. The Orca CK-12001 is a T-pull bar, 2 inch bar width, steel, in satin nickel. If the design intent is a bracket-style angle profile in a plated finish, the MP9116 is the match; the CK-12001 reads as a bar.

The Emtek Schaub collection covers several looks: the 8405 Select, the Alexander, the Art Deco, and the Bar cabinet pull, all catalogued by function as cabinet knob or pull. Where the specified item is the Emtek Bar pull and the look wanted is a clean modern profile, the Deltana MP9116 Modern Cabinet Angle Pull is aluminum at 9-1/16 inches with concealed screw installation, in Oil Rubbed Bronze, Brushed Nickel, or Polished Chrome. Where the drawing calls for the Art Deco or Alexander styling, those are decorative profiles the MP9116 does not reproduce.

No. The SDC SP50 is a 50mm spindle, a door control component that transmits turning motion through a lock or exit device. The Deltana MP9116 is a cabinet pull that mounts to the face of a door or drawer with concealed screws and has no spindle. Ordering the SP50 against a cabinet hardware takeoff will not produce a grip for the casework.