Emtek 3145 Mormont Brass Mortise Entrance Lockset - Dummy

Dummy function, so there is no latch and no working mechanism. The 3145 Mormont is a non-keyed, non-operating set used on the inactive leaf of a pair, on a closet or pantry door, or anywhere you want the handle to match the working openings without a latch. If you need a set that latches, order the keyed entrance or passage version of the mortise lock instead.

Yes, handing is required and it is not field reversible. The Mormont set is ordered left hand or right hand, and both are offered in every finish. Stand outside the door: the side the hinges are on is the hand. Get it wrong on a mortise set and the trim will not sit correctly on the door.

Standard mortise pocket per ANSI A115.1, with the backset at either 2-1/2 inches or 2-3/4 inches. If you are replacing an existing mortise lock in a door already prepped to A115.1, measure from the door edge to the center of the knob or lever hole to pick your backset, since the two are not interchangeable in an existing prep.

1-3/4 inches is the standard build, which covers most exterior and commercial-weight doors. Thicker doors are handled, but the thickness has to be called out on the order, so measure the door before you buy rather than assuming a standard set will make up the difference.

Sold as a complete set, and you choose the inside knob or lever style when you order. That choice is required, not optional. The range covers brass levers and knobs (Stuttgart, Athena, Luzern, Cortina, Milano, Round, Egg, Octagon), knurled and faceted contemporary bar styles (L-Square, T-Bar, R-Bar, Conical), and crystal and porcelain knobs (Bristol, Windsor, Diamond, Georgetown, Ebony, Ice White). Any brass knob, crystal or porcelain, or lever can be paired with the set.

No. The Mormont is a residential brass mortise set, solid brass body and trim, built for appearance-driven homes and light-traffic openings. For a commercial or institutional opening where a Grade 1 mortise lock is specified, look at the Cal-Royal NM8050 office/entrance or NM8080 storeroom, the Corbin Russwin ML2003 classroom, or the Hager 3800 Series. Those are the heavy-duty side of the aisle; the Emtek is not a substitute for them.

Put the working mortise entrance set on the active leaf and the 3145 Mormont dummy on the inactive one. The dummy uses the same brass trim and the same six finishes, so both leaves read identically, but there is no latch or mechanism behind it. Specify the hand of each leaf separately, and pick the same knob or lever style for both so the pair matches.

The Emtek 3145 Mormont is a dummy function mortise set, so it has no latch and no key operation. For a door that has to latch and lock, the Baldwin 6301 mortise lock body is an entrance/apartment function set built for doors 1-3/4 inch and over, offered as knob by knob or as the 6301LS lever by lever, both on a 2-1/2 inch backset. The 2-1/2 inch backset matches one of the two backsets the Mormont set is prepped for, so a door already mortised for the Emtek can take the Baldwin body in the same pocket.

The Emtek 3145 Mormont is a residential brass dummy set with no locking function at all. For a graded commercial opening, the Cal-Royal NM8080 is a heavy duty Grade 1 storeroom mortise lockset with an interchangeable core option for 1-3/4 inch doors, and the Cal-Royal NM8070 is the Grade 1 classroom version with an auxiliary deadlatch on the same 1-3/4 inch door thickness. The Corbin Russwin ML2003 covers classroom function as a Grade 1 ML2000 Series mortise lockset, also for 1-3/4 inch doors.

A privacy mortise lockset is the swap. The Cal-Royal NM8440 is a heavy duty Grade 1 privacy mortise lockset with a deadbolt for 1-3/4 inch doors, and the Hager 3840S is a Grade 1 privacy mortise lock on a 2-3/4 inch backset for doors 1-3/4 inch to 2 inch. The Emtek 3145 Mormont carries no privacy or keyed function and is prepped for a 1-3/4 inch door as standard, with thicker doors specified at order.

No, not without changing the door prep. The Emtek 3145 Mormont is a mortise lock using a standard mortise prep to ANSI A115.1, which is a rectangular pocket in the door edge. The Schlage PC10 is a Grade 1 passage cylindrical lock with a rose for 1-3/4 inch doors, and cylindrical prep is a bored hole, not a mortise pocket. If the door is already mortised, stay with a mortise body such as the Schlage PM010 Grade 1 passage latch mortise lock.

The Emtek 3145 Mormont is built for 1-3/4 inch doors as standard with thicker doors specified at order. Among working mortise locks, the Hager 3810E passage lock with escutcheon and the 3810S with rose both cover 1-3/4 inch to 2-1/2 inch on a 2-3/4 inch backset, the Hager 3850E office function covers the same 1-3/4 inch to 2-1/2 inch range, and the Baldwin 6310 entrance/storeroom body covers 1-3/8 inch and over on a 2-1/2 inch backset.

The Emtek 3145 Mormont carries a UL 180 minute fire rating with a standard mortise prep to ANSI A115.1. Among mortise peers, the Falcon MA101 Grade 1 heavy duty passage lock is fire rated, and the Schlage Electronics LEMD-GRW Grade 1 ENGAGE Series wireless mortise lock carries a 3 hour rating, as does the LEBMB-ADD Grade 2 mobile enabled mortise lock. Fire rating follows the whole assembly, so match the lock rating to the door label.

The Mormont mortise set carries a UL 180 minute fire rating. Note the function though: as a dummy it does not latch, and a fire door assembly generally needs a positive latching device on the active leaf. The dummy is for the inactive leaf or a non-rated opening; the rating matters when it is installed as part of a pair with a latching set on the other leaf.

Six finishes, each available in both hands: Oil Rubbed Bronze (US10B), Satin Nickel (US15), Flat Black (US19), Polished Chrome (US26), Unlacquered Brass (US3NL) and Satin Brass (US4). Because the same finish codes run across the Emtek brass line, you can carry one finish from the entry set through interior doors and dummy leaves. Unlacquered brass is the one to think about for a fleet: it is left uncoated and will patina over time, so new pieces will not match older ones straight away.

For a commercial dummy, the Schlage L0170 is a Grade 1 mortise half dummy lever trim for 1-3/4 inch doors. If the opening is an exit device rather than a mortise lock, the Falcon MESC600DT is dummy escutcheon lever trim for M9900 Series exit devices and is fire rated. The Emtek Mormont dummy is the residential brass option and is chosen for finish and style rather than duty level.

Emtek's brass mortise entrance locksets in this family are cut to Schlage C keyway, so a keyed Mormont set can be keyed alike with the rest of a Schlage C system by a locksmith. The 3145 itself is the dummy, so it takes no cylinder at all; the keyway matters when you are ordering the keyed entrance set for the same openings and want one key to run the house.

Yes. The Schlage L0170 is a half dummy trim, a Grade 1 non-keyed mortise lever unit in the L Series rated heavy duty for 1-3/4 inch doors. It gives one side a fixed lever with no working mechanism. The Emtek 3145 Mormont is a brass dummy mortise entrance set sold complete and ordered with any Emtek brass knob, crystal and porcelain, or lever trim, and it requires handing specified left or right; the Schlage half dummy is a single-side trim only.

A passage lock has a working latch that retracts with the handle but never locks; a dummy has no latch at all and the trim is fixed. The Schlage PM010 is a Grade 1 non-keyed passage latch mortise lock for 1-3/4 inch doors, and the Falcon MA101 is a Grade 1 heavy duty mortise passage lock with field reversible operation and a fire rating. Field reversible matters because the Emtek 3145 Mormont requires handing specified left or right at order.

They share the dummy function but not the application. The Falcon MESC600DT is a fire rated dummy escutcheon lever trim made for M9900 Series exit devices, so it mounts to an exit device rather than into a door mortise. The Emtek 3145 Mormont is a brass mortise dummy set that uses a standard mortise pocket per ANSI A115.1 and takes Emtek knob, crystal and porcelain, or lever trim. Do not order the Falcon trim for a mortised wood or hollow metal door with no exit device on it.

None of the electronic options are drop-in for a brass dummy set, but for a mortised door needing access control the Alarm Lock DL3500CR is a Grade 1 Trilogy electronic mortise lock with 300 user codes and classroom function for doors 1-5/8 inch to 1-7/8 inch, and the TownSteel FME-2000 is a Grade 1 heavy duty classroom mortise lockset with RFID for 1-3/4 inch doors. The Emtek 3145 Mormont is a non-electronic brass set.

No. The Emtek 3145 Mormont is a non-keyed dummy set with fixed trim. A mortise deadbolt is a separate keyed body with no handle function, such as the Sargent 4874 double cylinder mortise deadbolt on a 2-3/4 inch backset, or the Kaba Ilco 185 Series mortise lock in deadbolt function, which is supplied with no handing. If an opening needs both a handle and a bolt, those are two different bodies, not a substitution for one another.

The Emtek 3145 Mormont set is cut for the Schlage C keyway on its keyed siblings, so keyed openings built around Schlage C cylinders will key alike with the family. The Baldwin 6310 entrance/storeroom mortise body covers doors 1-3/8 inch and over on a 2-1/2 inch backset, which is one of the two backsets the Mormont prep uses, and the 6310190RRLS is the right hand reverse lever by lever version of that body.

Purely mechanical, no electronics and no keypad. If you want keyless on a mortise prep, that is a different class of product: the Alarm Lock Trilogy DL2700CR and DL3500CR are Grade 1 keypad mortise locks for 1-5/8 to 1-7/8 inch doors, and the Dormakaba E-Plex 2066 is an electronic pushbutton mortise lock. Those replace the lock body and prep, so they are a design decision, not an add-on to the Mormont.