Emtek 7205 Wrought Steel #5 7-1/8" Non-Keyed Sideplate Tubular Lockset, Privacy

It drops into a standard 2-1/8 inch cross bore and fits doors 1-3/8 to 1-3/4 inches thick. The backset is adjustable, 2-3/8 or 2-3/4 inches, so it covers both common bores. What it does need beyond a standard bored-lock prep is the sideplate mortise: the plate runs 7-1/8 inches, so the face of the door has to be routed for that plate. If you are replacing a plain rose knob, plan on that extra prep work.

Non-keyed. The 7205 is a privacy function, the bed and bath setup: it locks from the inside only, with an emergency release on the outside. There is no cylinder and no key. If you need a keyed entry opening, this is the wrong function.

Yes, and the order asks for it. Handing is required on the leverset because the lever has to swing down toward the pull side. Stand outside the door: if the hinges are on your right it is right hand, on your left it is left hand. Handing is a required selection on this lockset regardless of which trim you pick.

The Omnia D12036AC is a double cylinder deadbolt lever lockset with solid brass construction and a sideplate design, keyed on both sides. The Emtek 7205 Wrought Steel #5 sideplate lockset is non-keyed with a privacy/bed/bath function, so its inside is operated by turn rather than a cylinder. Double cylinder locks are restricted for egress in many occupancies, so confirm the local code for the door before specifying the D12036AC.

No. The Emtek 7205 Wrought Steel #5 sideplate lockset ships as a complete privacy set including the knob or lever, latch and strike plate, and it requires a 2-1/8 inch cross bore and a latch bore in the door edge. For a surface-mounted, non-latching leaf, the Omnia D12036PD is a solid brass dummy deadbolt lever lockset with plates on a 5-1/2 inch center to center, which mounts without any latch or strike.

It ships as a complete set: knob or lever trim, the latch, and the strike plate. The latch faceplate is available round corner or square corner so it can match an existing mortise in the door edge. No cylinder is included and none is used, since this is a privacy function.

No. The Wrought Steel #5 sideplate lockset is a residential lock, tubular type, with no commercial grade behind it. For corridor, stairwell or office openings in a multi-family or commercial building, use a Grade 1 or Grade 2 cylindrical or mortise lock instead. The 7205 is meant for interior bed and bath doors in homes.

The 7205 gives you a 7-1/8 inch wrought steel sideplate in Flat Black Steel or Satin Steel, a rustic look rather than a polished one. It is a privacy lock with no deadbolt, so on an entry door you would pair it with a separate deadbolt. If you want the sideplate styling carried into a deadbolt, Omnia builds sideplate deadbolt leversets: the D12036A single cylinder, the D12036AC double cylinder, and the D12036PD double dummy version at 5-1/2 inch center to center. Those are solid brass rather than steel, so the finishes will not be an exact match to the Emtek wrought steel.

Keep the 7205 for the bath and bedroom doors and order the passage version of the same Wrought Steel #5 sideplate for doors that only need to latch, or a dummy sideplate for a closet door that just pulls shut. Same 7-1/8 inch plate, same knob and lever styles (Lafayette, Normandy, San Carlos, Jamestown, Savannah, Madison Black, Madison Ivory) and the same two steel finishes, so the openings read as a set.

They are not interchangeable even though both are sideplate-style lever hardware. The Emtek 7205 is a 7-1/8 inch non-keyed tubular sideplate lockset in the Wrought Steel #5 series with a privacy/bed/bath function, adjustable 2-3/8 or 2-3/4 inch backset, and a door thickness range of 1-3/8 to 1-3/4 inches. The Omnia D12036A and D12036AC are deadbolt lever locksets, single and double cylinder respectively, and the D12036PD is a dummy with a 5-1/2 inch center to center plate layout. Deadbolt and dummy prep will not line up with the Emtek privacy latch bore, so treat the choice as a function decision made before the door is machined.

The Emtek 7205 is a residential privacy/bed/bath sideplate lockset built in the Wrought Steel collection with a steel substrate, offered in Flat Black Steel and Satin Steel, and ordered with a Wrought Steel knob or lever such as the Lafayette, Normandy or San Carlos lever or the Jamestown and Savannah knobs. The Omnia D12036A and D12036AC are solid brass constructions in single and double cylinder deadbolt configurations. So the decision is a privacy latch in a forged steel look versus a brass deadbolt lever set, and the two draw from different material families if you are trying to match an existing run of doors.

The sideplate and trim are wrought steel, which is what gives the collection its hammered, forged look and the Flat Black Steel and Satin Steel finishes. The latch hardware is brass. If you want a solid brass sideplate lockset instead, Omnia's D12036 series sideplate leversets are solid brass construction.