Emtek 8011 Modern 7" Non-Keyed Sideplate Lockset, Dummy (Pair) - Brass Tubular

No boring needed. The 8011 Modern 7 inch sideplate dummy set is surface mount, so there is no door prep to cut. That makes it a common pick for a closet, pantry, or French door leaf where you only want a pull and no working latch. It ships as a complete set with the knobs or levers included.

Handing is a required choice, right hand or left hand, and it matters for a leverset since the lever has to point the correct way. Knob styles are symmetric, but the order still asks for a hand. Pick the hand as you stand on the side the door opens toward you.

No. It is a non-keyed dummy with no latch and no cylinder, so it neither latches nor locks. Use it only where a roller catch, ball catch, or magnetic catch holds the door, or on an inactive leaf. If you need the door to latch, you want a passage set; if it needs to lock, a keyed or privacy set.

The Omnia D12036PD is a solid brass dummy deadbolt lever lockset with plates, spaced 5-1/2 inch center to center, and it carries a double dummy function. The Emtek 8011 is a non-keyed dummy sideplate lockset in brass with a 7 inch sideplate, sold as a pair with the knob or lever trim included. Both give you a fixed pull with a long plate rather than an operating latch, so the decision comes down to plate length and the 5-1/2 inch center to center spacing on the Omnia versus the 7 inch Emtek plate.

The Emtek 8011 is a non-keyed dummy, so it will not secure an opening. For a keyed sideplate lever set, the Omnia D12036A is a single cylinder deadbolt lever lockset in solid brass, and the Omnia D12036AC is the double cylinder version with a sideplate design. Single cylinder takes a key outside and a thumbturn inside; double cylinder takes a key on both sides, which is the one to look at for a door with glass beside the lock. Match the function to the opening before you order.

It is a double dummy, meaning trim on both faces of the door. Order one 8011 per opening if you want a matching pull inside and out, such as on a pair of French doors or a double closet.

Yes, and the choice is wide. The 8011 takes any Emtek brass knob or lever style, from modern shapes like the Ace, Spoke, T-Bar, L-Square and R-Bar to traditional Rope, Ribbon and Reed and Victoria, plus crystal knobs such as Bristol, Windsor and Georgetown. The trim is chosen when you order and comes in the box.

A sideplate set puts the knob or lever on a long backplate rather than a small round rose. The 8011 uses a 7 inch plate, which covers more of the door face and reads as a deliberate design element. It also hides old fastener marks or finish shadows left by previous hardware better than a small rose will.

The Omnia D12036PD is a solid brass double dummy lever lockset with plates, spaced 5-1/2 inches center to center, and it carries a dummy deadbolt above the lever for that full entry-set appearance. The Emtek 8011 is lever or knob only on a 7 inch plate. If the same opening later needs to actually lock, Omnia's D12036A is the single cylinder version and the D12036AC is double cylinder.

No. The Omnia D12036A is a single cylinder deadbolt lever lockset, which means it is keyed and bolts into the door. The Emtek 8011 is a non-keyed dummy that surface mounts with no door prep required. Swapping a dummy for the D12036A means boring the door for the cylinder and bolt, so it is a new prep, not a trim change. If the door only needs a stationary pull on a closet, pantry, or an inactive leaf of a pair, stay with the dummy.

Six: Oil Rubbed Bronze (US10B), Satin Nickel (US15), Flat Black (US19), Polished Chrome (US26), Unlacquered Brass (US3NL) and Satin Brass (US4). Unlacquered brass is the one that will patina over time rather than hold its as-shipped look, so keep that in mind if you are matching other hardware in a hallway.

It is a purely mechanical, non-electronic set. Tubular in construction, non-keyed, with no wiring, no cylinder and no electronic provision. Nothing about it accepts a keypad or motorized module.