Emtek 8075 Belmont 3-5/8" C-to-C Keyed Sideplate Lockset, Dummy (Pair) - Brass Tubular

It is a dummy set, so there is no latch operation and no key. The Belmont 8075 sideplate lockset in dummy function is pull-only trim: the knob or lever is fixed and the sideplate is decorative. Use it on a closet door, a pantry, or the inactive leaf of a double door where you only need something to grab. If you need the door to latch or lock, you need a passage, privacy, or keyed function instead.

3-5/8 inches center to center between the knob or lever bore and the upper sideplate position. That spacing decides whether it lines up with an existing sideplate prep, so measure the hole centers on the door before ordering. For reference, the Omnia D12036PD dummy deadbolt lever lockset with plates runs 5-1/2 inch center to center, so the two are not interchangeable on the same prepped door.

Handing is required, right hand or left hand, and it is part of the order. Emtek calls it out for leversets in particular because a lever has to point the correct way on the door. Stand outside the door: if the hinges are on your right it is right hand, hinges on the left is left hand.

The 8075 Belmont is a dummy set, so it has no latch operation or locking at all - it is surface mounted trim for a door that stays closed by other means. For a locking sideplate opening, the Omnia D12036A is a single cylinder deadbolt lever lockset in solid brass, keyed outside with a thumbturn inside. If you need key control from both faces, such as a door with glass beside it, the Omnia D12036AC is the double cylinder version of the same sideplate design.

The Omnia D12036PD is the nearest peer: a solid brass dummy deadbolt lever lockset with plates on a 5-1/2 inch center-to-center spacing. Both are non-operating dummy sideplate sets in brass. The difference that decides the order is the plate geometry - the Emtek 8075 Belmont is a 3-5/8 inch center-to-center sideplate, while the Omnia D12036PD is 5-1/2 inch center to center, so they are not interchangeable on an existing plate footprint or on a matching set of doors already trimmed to one spacing.

It ships as a pair, one dummy assembly for each face of the door. That is the configuration you want on a double door or on a door where both sides need a grip. If you only need trim on one face, a pair means you will have a spare side left over.

Any Emtek brass knob or lever style, and the list is long: levers include Stuttgart, Helios, Athena, Hermes, Luzern, Poseidon, Argos, Aston, Basel, Breslin, Dumont, Freestone, Geneva, Hercules, Mercury, Myles, Sion, Spencer, Triton, Cortina, Manning, Milano, Merrimack, Turino, Coventry, Elan, Ribbon and Reed, Rope, Rustic, Santa Fe, Wembley, Arts and Crafts and Hammered. Knobs include The Ace and Ace Knurled, Spoke, Orb, Round, Bern, Freestone, Hammered Egg, Laurent, Octagon, Square, Verve, Egg, Melon, Norwich, Providence, Waverly, Belmont, Lancaster, Ribbon and Reed, Rope, Victoria, Astoria, Ebony and Ice White, plus crystal options and the L-Square, T-Bar, R-Bar and Conical bar families in faceted, hammered, knurled, Tribeca, straight knurled and white marble. It is a required choice on the order.

No. The Omnia D12036A is a single cylinder deadbolt lever lockset, so it requires a cylinder and deadbolt bore that a dummy opening does not have. The Emtek 8075 Belmont is a non-keyed dummy pair, and its sideplate is 3-5/8 inch center to center against the Omnia's 5-1/2 inch spacing on the D12036 sideplate family. Swapping one for the other means new door prep and a different plate footprint, not a trim change.

Both are dummy sets intended for doors that do not need to latch. The Emtek 8075 Belmont is sold as a pair of surface-mounted brass sideplates on 3-5/8 inch center-to-center spacing, and the inside trim can be ordered in any Emtek brass knob or lever style, with handing specified for lever choices. The Omnia D12036PD is a double dummy solid brass lever set with plates at 5-1/2 inch center to center. Choose on plate length and trim style: the shorter Emtek plate suits narrower stiles, and the Omnia carries a longer plate.

Yes, and that is the usual reason people buy sideplate trim. The Belmont plate is available in five finishes and takes any Emtek brass knob or lever, so you can run the dummy version on closets and the inactive leaf of double doors while using working functions elsewhere with the same plate, finish and lever design. Order every opening in the same finish code and the same style code to keep them identical.