Emtek Lost Wax Cast Bronze Column 8" Door Pull

Standard mounting is thru-bolt with decorative caps, so the door gets drilled all the way through at the two 8 inch center to center points and the caps cover the fastener heads on the back side. Two other mounting options are offered: back-to-back, which pairs the pull with a matching pull on the opposite face and bolts the two together, and concealed screws, which hides the fasteners so no cap shows. Pick the mounting before you order, because it changes the part you receive.

Order the back-to-back version, part number BTB86156FB in Flat Black Bronze or BTB86156MB in Medium Bronze. That is a matched set for both faces bolted through the door, rather than one pull with capped fasteners showing on the reverse. Ordering two of the single thru-bolt version does not give you the same hardware.

Yes. Door thickness is asked for on the order because the pull is a thru-bolt part and the fasteners have to be the right length for the slab. Give the actual measured thickness of the door you are hanging it on, especially on a back-to-back set where the bolts have to reach through from one pull to the other.

The Emtek Column pull is a lost wax cast bronze pull with an 8 inch center-to-center and a 2 inch projection, specified for residential use. Where an opening needs a commercial heavy duty pull instead, the Ives 8103HD is a straight door pull in 1 inch round stock with through bolt mounting, and the Ives 8102HD is a straight pull in 3/4 inch round bar with 1-1/2 inch clearance. Both are cataloged at a heavy duty level, so they suit traffic the residential bronze Column pull is not rated for.

The Emtek Column pull is an 8 inch center-to-center pull with a 2 inch projection, which suits a cabinet, appliance or entry door pull application rather than a full-height entry grab. For a long single-side pull the Deltana SSP1210 is a 12 inch contemporary pull, and for a full-length back-to-back grab the Deltana SSPORBB24 is a 24 inch round offset pull supplied as a back-to-back pair. The ABH AB3330 series offset round end pull is offered with custom length options where a specific length is called out on the drawing.

The Emtek Column pull is a lost wax cast bronze pull specified for residential use. Where an opening has to satisfy ADA, the Ives 8145EZHD is a 45 degree offset door pull described as ADA compliant and supplied with heavy duty mounting hardware. That is the pull to specify on a barrier-free opening in place of the decorative bronze Column pull.

The Emtek Column pull is ordered in a back-to-back configuration under the BTB prefix, as in BTB86156FB in Flat Black Bronze and BTB86156MB in Medium Bronze. If a different look is wanted in a back-to-back set, the Deltana OHP620 is an off-set handle pull supplied as a back-to-back set for doors 1-1/8 inch to 1-3/8 inch thick, and the Deltana SSPOBB24 is a 24 inch back-to-back modern offset pull. The Column pull is an 8 inch center-to-center cast bronze pull, so it reads much shorter on the door than the 24 inch Deltana.

The Emtek Column pull is a plain cast bronze grip pull with an 8 inch center-to-center, thru-bolt mounted, with no cylinder prep. For an opening where the pull has to carry a night latch cylinder, the Cal-Royal PUL-175 is a night latch cylinder pull of stainless steel construction at 3-1/2 inch height. That is a different part with a cylinder hole in it, not a finish variation on the Column pull.

Yes. It is classed as a door or appliance pull, so an 8 inch center to center span works on a refrigerator panel, a pantry door or a tall cabinet front as well as a passage door. The 2 inch projection is what to check on an appliance, since that is how far the grip stands off the face.

It does. The Column pull sits in Emtek's Tuscany Bronze collection, cast bronze in the same Tuscany theme as the rest of that line, in Flat Black Bronze or Medium Bronze. If your other openings already carry Tuscany Bronze levers or knobs, order the pull in the same finish code, FB or MB, and the family reads consistently.

No. The Emtek Column is a pull, a graspable bronze handle with an 8 inch center-to-center and a 2 inch projection that a person wraps a hand around to draw the door open. A push plate is a flat plate mounted to the door face for the push side of a swing, such as the Trimco 1001-1 heavy duty push plate at 3 inch by 12 inch or the Trimco 1041 half-round push plate at 8 inch by 16 inch. The Trimco 1070 series is offered as classic push/pull plates at 3-1/2 inch by 15 inch, which pairs a plate with a pull rather than substituting a bare handle.

The Emtek Column pull is a cast bronze pull with a 2 inch projection off the face of the door and thru-bolt mounting. Among commercial pulls the straight form is represented by the ABH AB3300 flat end pull in 1.00 inch diameter and the ABH AB7200 solid stainless steel flat end pull in 7/8 inch diameter with through-bolt mounting; the offset form is represented by the ABH AB3310 offset flat end surface mount pull and the Ives 8169 C style offset pull in 1 inch diameter. Offset pulls angle the grip away from the door face, while a straight pull runs parallel to it.

The Emtek Column pull is lost wax cast bronze and is offered in Flat Black Bronze and Medium Bronze under the Tuscany Bronze collection. Where stainless is wanted instead of a bronze finish, the ABH AB7200 is a solid stainless steel flat end pull handle in 7/8 inch diameter with through-bolt mounting, and the Cal-Royal PUL-175 is of stainless steel construction. Stainless reads cooler and more contemporary than the warm cast bronze of the Column.

The Emtek Column pull is offered with concealed screws under the CS prefix, as in CS86156FB and CS86156MB, alongside the standard thru-bolt with decorative caps. If the choice is between brands, the ABH AB3310 offset flat end pull is a commercial grade surface mount pull, while the ABH AB7200 and the Ives 8103HD both use through-bolt mounting that carries fasteners across the door.

Two: Flat Black Bronze (FB) and Medium Bronze (MB). Both are on lost wax cast bronze, and both are available across all three mounting styles, so the finish choice does not limit you to one mounting. These are living bronze finishes on a solid cast body, part of Emtek's Tuscany Bronze collection, so expect them to read warmer and less uniform than a plated brass pull.

The pull projects 2 inches off the door face, and the grip sits inboard of that, so the hand space is under 2 inches. That is fine for a bare hand on a residential entry but tight with a work glove. If you want more room, the Ives 8102HD is a heavy duty straight pull stated at 1-1/2 inch clearance on a 3/4 inch round bar.