Emtek Lost Wax Cast Bronze Palermo 8" Door Pull

The Palermo pull measures 8 inches in height with 8 inch center-to-center hole spacing, and it stands 2 inches off the door face. Drill your two mounting holes 8 inches apart to match. The 2 inch projection is what gives you hand clearance behind the grip.

Three mounting choices. Standard is thru-bolt with decorative caps on the opposite face, so you see a finished cap where the bolt comes through. Back-to-back (BTB) pairs the pull with a matching Palermo pull on the other side and bolts the two together, which is what you want on a glass-front entry or a door pulled from both sides. Concealed screws (CS) hide the fasteners for a clean face. The BTB and CS versions carry a BTB or CS prefix on the part number, for example BTB86167MB or CS86167MB.

Yes, provide it. The Palermo is thru-bolted, so the fastener length has to match your door, and there is a door thickness field on the order for exactly that. Measure the actual slab, not the nominal size, and give it when you order.

It is classified as residential. For a commercial entrance, a school, or a healthcare corridor, look at a heavy duty commercial pull instead, such as the Ives 8103HD straight pull with through bolt mounting or the Ives 8145 45 degree offset EZ series pull. The Palermo is the right choice for a residence, a boutique, or a hospitality interior where the cast bronze look matters more than commercial duty cycles.

The Emtek Palermo 8 inch pull is a cast bronze residential pull with an 8 inch center-to-center and 2 inch projection. For a commercial opening, the Ives 8103HD is a heavy duty straight door pull with a 1 inch round bar and through bolt mounting, and the Ives 8102HD is a heavy duty straight pull with a 3/4 inch round bar and 1-1/2 inch clearance. Both are cataloged at a heavy duty level rather than a residential one.

Two: Flat Black Bronze (FB) and Medium Bronze (MB). Both are available on all three mountings, so part numbers run 86167FB and 86167MB for standard thru-bolt, with BTB or CS prefixes for the other mounting styles. These are lost wax cast bronze in Emtek's Tuscany Bronze collection, so expect the hand-finished variation typical of cast bronze rather than a uniform plated look.

Yes. It is classified as a door or appliance pull, so it works on a refrigerator panel, a pantry door, or a tall cabinet front as well as on a passage or entry door. Just confirm the panel thickness for the thru-bolt and that 8 inch center-to-center spacing lands where you want it on the face.

The Palermo is an 8 inch pull with 8 inch center-to-center, so it will look small on a tall glass or full-lite entry. For length, look at the Deltana SSP1210 12 inch contemporary pull single side, or the Deltana SSPOBB24 24 inch back-to-back offset pulls for a paired entry. Those are contemporary profiles rather than cast bronze, so they will not match a Tuscany theme.

It belongs to Emtek's Tuscany Bronze collection under the Palermo series, so it coordinates with other Palermo and Tuscany Bronze trim in the same FB or MB finish. If you are matching across a house or a set of units, order all the pulls in one finish code, since Flat Black Bronze and Medium Bronze are distinct and cast bronze finishes vary between production runs.

Yes. The Palermo is offered in a back-to-back mounting configuration under the BTB86167 prefix. Comparable back-to-back sets include the Deltana OHP620 off-set handle pull, sold as a back-to-back set for doors 1-1/8 inch to 1-3/8 inch thick, and the Sure-Loc PL-2KN knurled long door pull in a double-sided version. The Palermo differs in being a cast bronze pull with an 8 inch center-to-center.

The Palermo is offered with concealed screws under the CS86167 prefix. A plainer option with the same fastening approach is the Sure-Loc PL-1RD round long door pull, which is offered with concealed or thru-bolt mounting in a single-sided configuration. The Palermo route gives a lost wax cast bronze body in Flat Black Bronze or Medium Bronze.

They are not interchangeable. The Trimco 1070 series is a 3-1/2 inch by 15 inch push/pull plate, a flat plate covering the door face, and the Trimco 1001-1 is a 3 inch by 12 inch push plate with no grip at all. The Emtek Palermo is a grip pull with an 8 inch center-to-center and a 2 inch projection off the door, thru-bolted through the door leaf.

The Palermo is lost wax cast bronze. For stainless, the ABH AB7200 is a solid stainless steel flat end pull handle with a 7/8 inch diameter grip and through-bolt mounting, and the ABH AB3300 is a straight flat end commercial pull with a 1 inch diameter. Both are plain-profile commercial pulls rather than decorative bronze castings.

The Emtek Palermo is a residential cast bronze pull. For restroom openings, the Trimco 1035 Ultimate Restroom Pull is a heavy duty pull built for that application, and the Trimco 1041 is a heavy duty half-round push plate measuring 8 by 16 inches for the push side.

The Emtek Palermo is a straight pull with an 8 inch center-to-center and a 2 inch projection, so it will not match a C-style profile. The Ives 8169 is a C style offset solid door pull with a 1 inch diameter and heavy duty mounting, which is the closer match to that shape.

Solid lost wax cast bronze. The description also references brass content, which is normal for a cast bronze alloy. Cast bronze in a living finish like Medium Bronze will lighten at the grip points over time as hands wear the high spots, which is expected on a Tuscany Bronze piece rather than a defect. Flat Black Bronze shows that change less.

The ABH AB3310 is an offset flat end door pull for commercial surface mounting, and the ABH AB3330 is an offset round end pull with custom length options. Offset pulls angle the grip away from the door face along its length. The Emtek Palermo is a straight decorative pull with an 8 inch center-to-center and 2 inch projection, cast in bronze.

No. The Cal-Royal PUL-175 is a night latch cylinder pull, 3-1/2 inches high in stainless steel, designed to sit around a rim cylinder on a night latch application. The Emtek Palermo is an 8 inch center-to-center door or appliance pull in cast bronze with a 2 inch projection, with no cylinder cutout.