You may also like
NON-INS BTT SPLICE 9-7 AWG 1.03 LEN
Manufacturer Resources
Product Specs
- Country Of Origin:
- Mexico (MX)
- Product Subgroup:
- Splices
- Product Type:
- Non-Insulated Butt Splice
- Standards:
- UL E9809
- Temperature Range:
- 150 °C
- Voltage Rating:
- 600 V
- Department:
- Electrical
- Product Group:
- Wire Termination
- Product Color:
- Metallic
- Product Material:
- Copper
Sta-Kon 2D-8 – Frequently Asked Questions
1) What wire sizes does the Sta-Kon 2D-8 butt splice accept?
The Sta-Kon 2D-8 is sized for 9 through 7 AWG stranded copper conductors, one wire into each barrel end. Both wires going into the splice need to fall in that range; smaller conductors like 12 or 14 AWG will not crimp reliably in this barrel and call for a smaller splice.
2) Is the 2D-8 splice insulated, and do I need to cover it after crimping?
It is a non-insulated butt splice, so the bare metallic barrel is exposed after crimping. You need to insulate the joint yourself with heat shrink tubing or tape rated for the circuit. That is also why it is used where a pre-insulated splice would not survive the heat.
3) What voltage and temperature is the Sta-Kon 2D-8 rated for?
Rated 600 V, with a temperature range to 150 C. That high temperature limit is what makes a non-insulated barrel the right choice in motor connection boxes, luminaire housings, and heater terminations where nylon or vinyl insulated splices would be out of range.
4) Is this butt splice UL listed for use in commercial electrical work?
Yes. The 2D-8 carries UL file E9809, so it can be used where an inspector wants a listed connector on the splice. Keep in mind a listing applies to a properly made crimp with the correct die, so the tool matters as much as the connector.
5) Can I use the Sta-Kon 2D-8 on aluminum wire?
No. It is a copper connector intended for copper conductors. Aluminum conductors require a connector specifically listed AL/CU for that service, so this splice is the wrong part for an aluminum feeder or branch circuit.
6) How long is the Sta-Kon 2D-8 splice barrel?
The 2D-8 is a 1.03 length butt splice. Worth knowing before you order if you are splicing inside a tight junction box or a motor peckerhead, since the finished joint plus the heat shrink you add over it needs room to lie without stressing the conductors.
7) What part number do I order for a non-insulated 9-7 AWG butt splice from Sta-Kon?
Order Sta-Kon part number 2D-8. It is the single model on this product, a non-insulated copper butt splice for 9-7 AWG, made in Mexico.
How fast can I get the Sta-Kon 2D-8 delivered?
Most orders ship the same day from our distribution partners, with quick delivery throughout the
continental
U.S.
Need it urgently? Contact Us for expedited shipping options.
Can I return it if it doesn’t work for me?
Yes—ZenSupply offers a hassle-free return policy. If the product isn’t the right fit,
reach out to our support team for a return authorization or setup a return by following our return instructions.
Does the Sta-Kon 2D-8 come with a warranty?
Absolutely. The Sta-Kon 2D-8 is backed by a manufacturer’s warranty.
For full warranty terms, check the product documentation or Contact Us.
How do I get technical support or installation help for the Sta-Kon 2D-8?
You can call, text, or email our expert support team for fast answers. We’re here to help with
product
selection,
installation tips, and troubleshooting. Contact Us
Why buy the Sta-Kon 2D-8 from ZenSupply?
ZenSupply makes it easy to get the commercial door hardware you need—fast shipping, expert support,
and
rewards on
every order.
Our team is always ready to help you choose the right product for your project.