You may also like
NON-INS BTT SPLICE No6 AWG LEN 1.12
Manufacturer Resources
Product Specs
- Country Of Origin:
- Mexico (MX)
- Product Subgroup:
- Wire Connectors
- Product Type:
- Butt Splice
- Temperature Range:
- 150 °C
- Voltage Rating:
- 600 V
- Department:
- Electrical
- Product Group:
- Wire Connectors & Terminals
- Product Color:
- Metallic
- Product Material:
- Copper
Sta-Kon 2.00E-06 – Frequently Asked Questions
1) What wire size does the Sta-Kon 2E-6 butt splice take?
The Sta-Kon 2E-6 is sized for No. 6 AWG conductor on both ends. It is a straight butt splice, so it joins two 6 AWG wires end to end rather than stepping between sizes. Overall length is 1.12 inches.
2) Is the Sta-Kon 2E-6 splice insulated, and do I need to cover it after crimping?
It is a non-insulated butt splice, bare copper with a metallic finish. There is no sleeve on the barrel, so after crimping you have to insulate the joint yourself with heat shrink or tape rated for the circuit. If you would rather the insulation come on the part, choose an insulated butt splice instead.
3) Will this splice hold up in a hot location like a luminaire or motor junction box?
The 2E-6 is rated to 150 degrees C, so it suits high temperature terminations such as fixture whips, motor leads and heating equipment boxes. Being bare copper, the limiting factor is usually the insulating cover you add over it, not the splice barrel.
4) Do I need a special crimp tool for a 6 AWG non-insulated butt splice?
Yes. A bare copper barrel this size needs a crimper with a die for 6 AWG non-insulated terminals, usually a heavy hand tool or hydraulic crimper. Pliers or an insulated-terminal crimper will not form a sound joint on the 2E-6. The tool is not supplied with the splice.
5) Can I use the Sta-Kon 2E-6 on aluminum conductor?
No. The barrel is copper and intended for copper conductor. For aluminum or mixed aluminum-to-copper runs you need a splice or connector specifically marked AL9CU or AL/CU with the proper inhibitor compound.
6) What is the Sta-Kon 2E-6 part used for on the job?
It is a wire termination splice for joining two 6 AWG copper conductors inline, crimped rather than twisted, where a mechanical connector or wire nut is not wanted. Common uses are feeder tap repairs, motor and fixture lead extensions, and panel wiring where a low-profile inline joint is needed.
7) Where is the Sta-Kon 2E-6 made, and what part number do I order by?
Order it as Sta-Kon model 2E-6. Country of origin is Mexico.
How fast can I get the Sta-Kon 2.00E-06 delivered?
Most orders ship the same day from our distribution partners, with quick delivery throughout the
continental
U.S.
Need it urgently? Contact Us for expedited shipping options.
Can I return it if it doesn’t work for me?
Yes—ZenSupply offers a hassle-free return policy. If the product isn’t the right fit,
reach out to our support team for a return authorization or setup a return by following our return instructions.
Does the Sta-Kon 2.00E-06 come with a warranty?
Absolutely. The Sta-Kon 2.00E-06 is backed by a manufacturer’s warranty.
For full warranty terms, check the product documentation or Contact Us.
How do I get technical support or installation help for the Sta-Kon 2.00E-06?
You can call, text, or email our expert support team for fast answers. We’re here to help with
product
selection,
installation tips, and troubleshooting. Contact Us
Why buy the Sta-Kon 2.00E-06 from ZenSupply?
ZenSupply makes it easy to get the commercial door hardware you need—fast shipping, expert support,
and
rewards on
every order.
Our team is always ready to help you choose the right product for your project.