Orca Hardware Bachelor Collection, Round Ring Cabinet Pull Knob, 1-1/4" Diameter

It's a round ring style knob measuring 1-1/4 inches in diameter, model CK-16030 from Orca Hardware's Bachelor Collection. The ring shape gives you something to hook a finger through, so it works like a small pull on drawer fronts as well as on doors.

The knob is zinc alloy, and Orca rates the Bachelor Collection for residential use. Zinc alloy is a cast material, which is why it holds a crisp ring profile at a low cost, and it's normal for apartment and multi-family kitchen and bath cabinetry. For heavier commercial-duty cabinetry, a solid brass pull such as the Omnia 1970 or the Deltana SBP35 square bar pull is the sturdier material.

No. The CK-16030 is listed as not ADA compliant, and Orca rates it residential. ADA operable-parts guidance favors hardware you can work without tight grasping or pinching, which a small ring knob does not satisfy. For institutional casework, spec a bar or wire pull instead, such as the Emtek Bar cabinet pull or a Trimco 553 Series drawer pull.

A single-screw knob like the Orca CK-16030 mounts through one hole, so it swaps straight onto doors and small drawers already drilled for a knob. Wider drawers and appliance fronts are usually better served by a two-screw pull, where you have to match the existing center-to-center spacing: the Schaub 10010 Sabre edge pull is 3 inch centers, the Schaub 10011 is 4 inch, the Schaub 10012 is 5 inch, and the Omnia 1968/102 is 4 inch. Measure hole to hole before you decide.

The CK-16030 is a 1-1/4 inch diameter round ring cabinet knob, so it mounts on a single screw. For a drawer front already bored on two centers, a center-to-center pull is the right part: the Trimco 553 Series drawer pull is 3 inch center-to-center, the Trimco 562 Series is offered in 3-1/2 inch, 4 inch and 96mm center-to-center, the Deltana SBP35 modern square bar pull is 3-1/2 inch, and the Omnia 1968/102 is 4 inch center-to-center. Match the spacing to the existing holes to avoid re-drilling the front.

No. The Orca Hardware Bachelor Collection CK-16030 knob is zinc alloy. If the specification calls for forged solid brass, the Omnia 1969, 1970 and 1971 modern cabinet pulls are forged solid brass, as is the Deltana SBP35 square bar pull and the Schaub 10010 Sabre edge pull. Substrate is the main difference to weigh when you are matching an existing brass hardware package.

A round ring knob like the CK-16030 stands off the face by design. Where projection is a problem - sliding doors, bypass panels, or a tight galley run - the Schaub Sabre edge pulls mount at the door edge instead: 10010 at 3 inch center-to-center, 10011 at 4 inch, and 10012 at 5 inch. Omnia publishes projection for its pulls as well, 1-1/4 inch on the 1970 and 1-3/16 inch on the 1969 and 1971, if you need a surface pull with a known standoff.

Two finishes: Oil-Rubbed Bronze and Satin Nickel. If you're mixing this with existing hardware in a kitchen, Satin Nickel is the one that reads closest to brushed nickel appliance trim, while Oil-Rubbed Bronze runs dark with warm undertones.

It's not the right choice there. A 1-1/4 inch ring knob gives you very little leverage against a heavy appliance panel or a tall pantry door. For that, use an appliance-scale pull such as the Schaub 79-8 Steamworks 8 inch cabinet pull, which is catalogued as an appliance pull.

The Bachelor Collection round ring knob is one model, CK-16030, in one 1-1/4 inch diameter with two finish choices, Oil-Rubbed Bronze and Satin Nickel. That makes it straightforward to standardize: pick one finish and every door and drawer in the unit gets the identical part number, no size or center-to-center variables to track.

Orca's ring knob is zinc alloy. If the job calls for forged solid brass, the Omnia modern cabinet pull series are the brass options we carry, including the 1969 and 1971 at 1-3/16 inch projection and the 1970 at 1-1/4 inch projection. Note those are pulls rather than ring knobs, so the mounting hole pattern differs.

The Orca Hardware Bachelor Collection CK-16030 round ring knob is offered in oil-rubbed bronze and satin nickel. If the design package calls for something outside those two, the Emtek Select 8405 and the Emtek Alexander, Art Deco and Bar cabinet pulls from the Schaub Collection are all catalogued as cabinet knob/pull and are specified by finish, so you can hold the same function and change the finish family.

The Orca Bachelor Collection CK-16030 is a round ring knob and is not ADA compliant. Where an easier grip is wanted, a bar or center-to-center pull gives a loop you can hook rather than pinch: the Emtek Bar cabinet pull, the Deltana SBP35 3-1/2 inch square bar pull, and the Trimco 562 Series in 3-1/2 inch, 4 inch or 96mm center-to-center are all bar-style options. Confirm the requirement with your specifier for the facility type.

No - they are unrelated parts despite both being small hardware items. The CK-16030 is a residential cabinet knob, while the SDC SP50 is a 50mm spindle for door controls. The SP50 drives a lock or exit device mechanism and has no cabinet mounting function.