Orca Hardware CP-23160 Tahoma Handle Pull, 160 mm CTC

No. The Tahoma CP-23160 is rated for residential use and it is not ADA compliant, so it should not be specified where an accessible-reach or ADA-operable hardware requirement applies. For commercial cabinet and drawer work, look at a pull specified for that duty instead.

The Tahoma CP-23160 will not fit those holes at 160 mm centers. For 3 inch centers the Trimco 553 Series drawer pull matches, and the Trimco 562 Series covers 3-1/2 inch, 4 inch, and 96 mm. The Omnia 1968/102 is also a 4 inch center-to-center pull in forged solid brass.

The Orca CP-23160 Tahoma is drilled for 160 mm center-to-center only, so it will not land on a 4 inch pattern. For a 4 inch spacing, the Omnia 1968/102 is a modern cabinet pull in forged solid brass with 4 inch center-to-center spacing, and the Schaub 10011 Sabre Collection edge pull is a solid brass pull on 4 inch center-to-center. The Omnia mounts as a face pull like the Tahoma; the Schaub Sabre is an edge pull, which mounts at the edge of the door or drawer front rather than on the face.

The Orca CP-23160 Tahoma is a handle pull on 160 mm center-to-center spacing in a transitional style. If you want a comparable bar-form cabinet pull from another line, the Emtek Bar Cabinet Pull in the Schaub Collection is a cabinet knob/pull in Emtek's Bar series, and the Omnia 1969 is a modern cabinet pull in forged solid brass with a 1-3/16 inch projection. Both serve the same job of a door or drawer face pull; confirm the center spacing you need matches your existing drilling before you swap, since 160 mm is a metric spacing and the Omnia and Emtek lines are sold across their own spacing ranges.

The Orca CP-23160 Tahoma is specified for residential application. For a commercial or MRO casework package, the Trimco 553 Series drawer pull at 3 inch center-to-center and the Trimco 562 Series in 3-1/2 inch, 4 inch and 96 mm center-to-center options are institutional drawer pull lines, and the Deltana SBP35 Modern Square Bar Pull is a 3-1/2 inch heavy-duty solid brass pull. Note that none of these match the Tahoma's 160 mm drilling, so a swap on existing casework means new holes or a backplate.

Four finishes: Black, Oil-Rubbed Bronze, Rose Gold, and Satin Nickel. If you are outfitting a full kitchen or a run of units and want everything to match, order all the pulls in one go so the finish lot stays consistent across the job.

None. It is pull trim only, listed as a dummy/pull function, so it is a grab handle that mounts through the door or drawer front with two screws. Any catch, latch, or lock on the cabinet is separate hardware.

At 160 mm centers the Tahoma handle is long enough to suit wider drawer fronts as well as tall cabinet and pantry doors. On a narrow door stile it can look oversized, so many kitchens mix the 160 mm on drawers with a shorter center spacing on the doors.

Tahoma is a transitional handle pull, so it sits between traditional and modern cabinetry. If you want a squarer, more contemporary line, the Deltana SBP35 Modern Square Bar Pull in solid brass or the Emtek Bar Cabinet Pull from the Schaub Collection go that direction. For a forged solid brass modern profile, the Omnia 1968/102 is a 4 inch center-to-center option, though note that is a different hole spacing than 160 mm.

The Orca CP-23160 Tahoma is a 160 mm center-to-center cabinet pull specified for residential cabinet doors and drawers. Appliance panels normally call for a longer, heavier pull on wider centers - the Schaub 79-8 Steamworks 8 inch cabinet pull is catalogued as an appliance pull for that purpose. Running the Tahoma on an appliance panel puts the two fasteners much closer together than the panel's prep typically allows.

No. The Orca CP-23160 Tahoma is a handle pull that mounts on the face of a cabinet door or drawer front on 160 mm centers. The Schaub 10010, 10011 and 10012 Sabre pulls are edge pulls, in 3 inch, 4 inch and 5 inch center-to-center spacings respectively - they are meant to sit along the edge of the panel and are cut in flush rather than standing off the face. If the cabinet was designed around a face-mounted handle, the Sabre will change both the look and the prep.

The Orca CP-23160 Tahoma is a transitional-style handle pull in the 23-Tahoma Collection, offered in Black, Oil-Rubbed Bronze, Rose Gold and Satin Nickel. If you want a more ornamental profile, the Emtek Art Deco Cabinet Pull and the Emtek Alexander Cabinet Pull, both in the Schaub Collection, are cabinet knob/pulls in their own Art Deco and Alexander series. The Emtek SELECT 8405 is another Schaub Collection cabinet knob/pull. Match center-to-center spacing to your existing 160 mm drilling if you are replacing rather than building new.

Projection matters where a pull sits near a wall return or an adjacent appliance. Among the comparable modern pulls, the Omnia 1970 is a forged solid brass cabinet pull with a 1-1/4 inch projection, while the Omnia 1969 and Omnia 1971 are both forged solid brass with a 1-3/16 inch projection. The Orca CP-23160 Tahoma is a transitional handle pull on 160 mm centers; if your clearance is tight, measure the opening swing before committing to any of them.

No. The Orca CP-23160 Tahoma is a cabinet handle pull on 160 mm centers with a dummy or pull-trim function, meaning it has no latching mechanism. The SDC SP50 is a 50 mm spindle in SDC's door controls line - a lock component, not a cabinet pull. They do not cross-reference in any way, so do not order the SP50 expecting cabinet hardware.