You may also like
Rockwood BF157A47 Offset Single Bar Set, 1" Diameter Pull, Pull 9" CTC, Push 33" CTC
Model: ROC-BF157A47
Rockwood BF157A47 Series 47 Offset Single Bar SetThe Rockwood BF157A47 is a Series 47 offset single bar set with a 1" diameter pull bar. Pull side: 9" center-to-center. Push side: 33"...
Rockwood
Starting at
$173.19
$148.00
ROCKWOOD Series 47 Straight Single Bar Sets
Material: Aluminum, brass, bronze, stainless steel;
Finishes: Available in standard architectural finishes;
Options:
- Engraving “PUSH” or “PULL”. Specify handing
- Base plates available similar to those shown on page A12 — use BP prefix (BP11047)
when ordering - Heavy duty versions of most fastening types available — use suffix HD to fastening type
number (11047 T3HD)
NOTE: Pull bar Projection : 3-1/2" for Stainless Steel and 3" for Aluminum, Brass and Bronze.
ROCKWOOD OVERVIEW
Rockwood products are normally used on all types of institutional buildings, offices, retail, educational, detention, sports facilities, hotel and restaurant, and finer residences.
ENVIRONMENTAL MANAGEMENT
ASSA ABLOY is commited to protecting the quality of the environment as well as the health and safety of its employees, customers, and the community. Please see our Environmental Health and Safety Policy for details on how we are dedicated to this commitment.
RESOURCES & DOWNLOADS
Manufacturer Resources
Product Specs
- Product Group:
- Door Trim and Accessories
- Subcategory:
- Push and Pull Bars
- Product Subgroup:
- Door Pulls, Push and Pull Plates
- Product Type:
- Door Pulls
- ANSI/BHMA:
- ANSI A156.6, J504
- Clearance:
- 2"
- Commercial/Residential:
- Commercial
- Product Model:
- 11047
- (CTC) Center-to-Center:
- 8"
- Product Projection:
- 3-1/2"
- Product Category:
- Door Trim and Accessories
- Product Substrate:
- Aluminum, Brass, Bronze, Stainless Steel
- Department:
- Door Hardware
Rockwood 11047CT3-32D – Frequently Asked Questions
1) How far does the Rockwood 11047 pull bar stick out from the door?
Projection is 3-1/2 inches on the stainless steel version and 3 inches in aluminum, brass, and bronze, with 2 inches of hand clearance between the bar and the door face. That difference matters in a vestibule or anywhere a pair of doors swings toward each other, and it matters at a wall return where a 3-1/2 inch bar can catch. If you have tight side clearance, spec the aluminum or brass bar rather than the stainless.
2) Is the Rockwood 11047 bar set rated for a commercial entrance or is it a residential pull?
It is a commercial door pull, built to ANSI A156.6, J504. Rockwood bar sets of this kind go on institutional buildings, offices, retail, schools, detention, sports facilities, hotels and restaurants. If you are standardizing pulls across a facility, the A156.6 J504 designation is the line to put on the spec.
3) I need an offset pull instead of a straight bar - what should I use in place of the Rockwood 11047?
The Rockwood 11047 is a straight bar, so the hand does not clear the door face by more than the 2 inch clearance and 3-1/2 inch projection the bar itself provides. When the opening calls for an offset so the grip angles away from the door, the Ives 8145EZHD is a 45 degree offset pull with heavy duty mounting hardware and is ADA compliant, and the Ives 8169 is a C style offset solid pull at 1 inch diameter, matching the 11047 bar diameter. On the ABH side, the AB3310 is an offset flat end pull for surface mount and the AB3330 is an offset round end pull available in custom lengths.
4) What finishes can I get the Rockwood 11047 straight bar set in?
Three finishes: 315 black anodized aluminum, 613 satin bronze oil-rubbed, and 630 satin stainless steel. Note that the finish decides the metal, and the metal decides the projection, so 630 gives you the 3-1/2 inch stainless bar while 315 is the 3 inch aluminum. Property managers matching a run of existing openings should pick the number, not the description, since 630 and 613 read very differently in daylight.
5) Can I get PUSH and PULL engraved on the Rockwood 47 series bars?
Yes, engraving of PUSH or PULL is an option on the Series 47 bar sets, and you have to specify handing when you order it, because the lettering has to read correctly from the approach side. Get the handing wrong and you have a bar that says PULL on the push face. On an unlabeled set handing does not matter, so if you are ordering plain bars you can skip that call.
6) How do I order a heavier duty version of the Rockwood 11047 for a high traffic entrance?
Add the suffix HD to the fastening type number. A heavy duty version is offered on most fastening types, written as 11047 T3HD. That is the one to spec on a school entrance, a hospital corridor, or any opening seeing constant hand traffic. If you would rather buy a heavy duty pull outright, the Ives 8103HD is a 1 inch round straight pull with through-bolt mounting at the same bar diameter.
7) Can I add a base plate under the Rockwood 11047 bars?
Base plates are available for the 47 series, ordered by putting a BP prefix in front of the model number, so the 11047 becomes BP11047. Worth doing where the door face is already drilled from previous hardware, or where you want a defined mounting footprint on a glass-front or aluminum stile door rather than bare posts on the face.
8) What metal is the Rockwood 11047 bar set made from, and which should I pick for an exterior door?
The 47 series bars are made in aluminum, brass, bronze, and stainless steel. For an exterior entrance or a coastal or wash-down environment, the 630 satin stainless is the one to take, and it is also the version with the 3-1/2 inch projection. Aluminum in 315 black anodized is the lighter interior option at 3 inch projection. Bronze in 613 oil-rubbed will change appearance with handling over time, which is the point on a hospitality or finer residential opening and usually not what an institutional buyer wants.
9) Is 2 inches of clearance behind a door pull enough for a gloved hand?
The 11047 gives 2 inches of clearance between the 1 inch bar and the door face. That is workable for a bare or lightly gloved hand and is normal for commercial bar sets. If crews are working in heavy winter gloves and you want more room, the Ives 8102HD is a heavy duty straight pull with a 3/4 inch round bar and 1-1/2 inch clearance, which is tighter, so it is not the fix. Stay with the 2 inch clearance of the 11047 for the roomier grip.
How fast can I get the Rockwood 11047CT3-32D delivered?
Most orders ship the same day from our distribution partners, with quick delivery throughout the
continental
U.S.
Need it urgently? Contact Us for expedited shipping options.
Can I return it if it doesn’t work for me?
Yes—ZenSupply offers a hassle-free return policy. If the product isn’t the right fit,
reach out to our support team for a return authorization or setup a return by following our return instructions.
Does the Rockwood 11047CT3-32D come with a warranty?
Absolutely. The Rockwood 11047CT3-32D is backed by a manufacturer’s warranty.
For full warranty terms, check the product documentation or Contact Us.
How do I get technical support or installation help for the Rockwood 11047CT3-32D?
You can call, text, or email our expert support team for fast answers. We’re here to help with
product
selection,
installation tips, and troubleshooting. Contact Us
Why buy the Rockwood 11047CT3-32D from ZenSupply?
ZenSupply makes it easy to get the commercial door hardware you need—fast shipping, expert support,
and
rewards on
every order.
Our team is always ready to help you choose the right product for your project.