You may also like
ROCKWOOD Series 47 Straight Single Bar Sets
Material: Aluminum, brass, bronze, stainless steel;
Finishes: Available in standard architectural finishes;
Options:
- Engraving “PUSH” or “PULL”. Specify handing
- Base plates available similar to those shown on page A12 — use BP prefix (BP11047)
when ordering - Heavy duty versions of most fastening types available — use suffix HD to fastening type
number (11047 T3HD)
NOTE: Pull bar Projection : 3-1/2" for Stainless Steel and 3" for Aluminum, Brass and Bronze.
ROCKWOOD OVERVIEW
Rockwood products are normally used on all types of institutional buildings, offices, retail, educational, detention, sports facilities, hotel and restaurant, and finer residences.
ENVIRONMENTAL MANAGEMENT
ASSA ABLOY is commited to protecting the quality of the environment as well as the health and safety of its employees, customers, and the community. Please see our Environmental Health and Safety Policy for details on how we are dedicated to this commitment.
RESOURCES & DOWNLOADS
Manufacturer Resources
Product Specs
- Product Group:
- Door Trim and Accessories
- Subcategory:
- Push and Pull Bars
- Product Subgroup:
- Door Pulls, Push and Pull Plates
- Product Type:
- Door Pulls
- ANSI/BHMA:
- ANSI A156.6, J504
- Clearance:
- 2"
- Commercial/Residential:
- Commercial
- Product Model:
- 11147
- (CTC) Center-to-Center:
- 10"
- Product Projection:
- 3-1/2"
- Product Category:
- Door Trim and Accessories
- Product Substrate:
- Aluminum, Brass, Bronze, Stainless Steel
- Department:
- Door Hardware
Rockwood 11147 313 33CTC – Frequently Asked Questions
1) How far does the Rockwood 11147 pull bar stick out from the door face?
Projection is 3-1/2 inches on the stainless steel version and 3 inches in aluminum, brass, and bronze, with 2 inches of hand clearance between the bar and the door. Worth checking against your traffic path: on a door that swings into a corridor or next to a wall return, that 3-1/2 inch stainless projection is what decides whether the bar clears.
2) Does the Rockwood 11147 meet ANSI A156.6 for door pulls?
Yes. The 11147 bar set is built to ANSI A156.6, type J504. If you are writing a spec for an institutional or government job that calls out A156.6 architectural door trim by type number, J504 is the line this satisfies.
3) Can I get the Rockwood 11147 in a heavy duty version for a high traffic entrance?
Yes. Rockwood offers heavy duty versions of most fastening types on these bar sets by adding the suffix HD to the fastening type number, written as 11047 T3HD in the catalog. For a school entry, a hospital corridor, or an apartment building lobby door that gets kicked and hauled on all day, that is the one to specify. Also worth ordering with base plates, which use the BP prefix (BP11047) and spread the load at the mounting points.
4) What finishes does the Rockwood 11147 straight bar set come in?
Three: 313 dark bronze anodized aluminum, 613 satin bronze oil-rubbed, and 630 satin stainless steel. Note the material follows the finish. 313 is anodized aluminum and 630 is stainless, so if you pick 630 you get the 3-1/2 inch projection, while the aluminum and bronze finishes project 3 inches. For matching a fleet of entrances across a property, 630 satin stainless is the one that lines up with most modern storefront and commercial trim.
5) The door opening needs an offset pull rather than a straight bar. What replaces the Rockwood 11147?
A straight bar set puts the grip parallel to the door face, which does not suit every opening. For an offset grip in the same commercial class, the ABH AB3310 is an offset flat end door pull handle for surface mounting, and the ABH AB3330 is an offset round end pull offered with custom length options. The Ives 8145EZHD is a 45 degree offset pull with heavy duty mounting hardware, described as ADA compliant. The Ives 8169 is a C style offset solid pull in 1 inch diameter with heavy duty mounting, matching the 1 inch bar diameter of the Rockwood 11147 pull while changing the geometry from straight to C style.
6) Do I have to specify handing when ordering a Rockwood 11147 bar set?
Only if you want the bar engraved. The 11147 takes optional PUSH or PULL engraving, and handing must be specified with that option so the lettering reads correctly for the swing. Plain, unengraved bars do not need handing called out.
7) Straight bar pull or offset pull - which should I use on an entrance door?
The 11147 is a straight bar, mounted parallel to the door edge with 2 inches of clearance behind it, which is the standard look on glass front and full-height entrances and the easiest to match across a run of doors. An offset pull angles the grip away from the door face and gives more knuckle room where a lock or a narrow stile crowds the mounting. If that is your situation, the ABH AB3310 offset flat end pull, the ABH AB3330 offset round end, or the Ives 8169 C style offset 1 inch diameter pull cover it. The Ives 8145 is a 45 degree offset pull.
8) Which material should I pick for a Rockwood 11147 on an exterior door?
Stainless steel, ordered as the 630 satin stainless finish. It holds up outdoors and in coastal or wash-down conditions better than the anodized aluminum or the oil-rubbed bronze, and it is the finish most likely to already be on the rest of a commercial entrance. The trade-off is projection: stainless projects 3-1/2 inches versus 3 inches for aluminum, brass, and bronze, so measure your clearance before you commit.
9) What is the difference between the Rockwood 11147 and the Ives 8102HD in bar size?
The Ives 8102HD is a heavy duty straight door pull built on a 3/4 inch round bar with 1-1/2 inch clearance. The Rockwood 11147 uses a 1 inch diameter bar with 2 inch clearance and a 3-1/2 inch projection. That clearance figure is the knuckle room behind the bar, so a facility standardizing on gloved-hand or heavy traffic openings will feel the half inch. If the goal is to match an existing 1 inch bar diameter rather than 3/4 inch, the Ives 8103HD is the 1 inch round straight pull in that line.
10) I only need a pull on one face, not a full bar set. What is the simpler option next to the Rockwood 11147?
A single side pull drops the push bar entirely. The Deltana SSP1210 is a 12 inch contemporary pull furnished single side, and the ABH AB7200 is a solid stainless steel flat end pull handle in 7/8 inch diameter with through-bolt mounting. The ABH AB3300 straight flat end pull is the 1 inch diameter option, matching the bar diameter of the Rockwood 11147 pull. Going single side means the opposite face is left to a separate push plate or bar if the opening needs one, which is the trade against the Rockwood 11147 covering both faces under one model number.
How fast can I get the Rockwood 11147 313 33CTC delivered?
Most orders ship the same day from our distribution partners, with quick delivery throughout the
continental
U.S.
Need it urgently? Contact Us for expedited shipping options.
Can I return it if it doesn’t work for me?
Yes—ZenSupply offers a hassle-free return policy. If the product isn’t the right fit,
reach out to our support team for a return authorization or setup a return by following our return instructions.
Does the Rockwood 11147 313 33CTC come with a warranty?
Absolutely. The Rockwood 11147 313 33CTC is backed by a manufacturer’s warranty.
For full warranty terms, check the product documentation or Contact Us.
How do I get technical support or installation help for the Rockwood 11147 313 33CTC?
You can call, text, or email our expert support team for fast answers. We’re here to help with
product
selection,
installation tips, and troubleshooting. Contact Us
Why buy the Rockwood 11147 313 33CTC from ZenSupply?
ZenSupply makes it easy to get the commercial door hardware you need—fast shipping, expert support,
and
rewards on
every order.
Our team is always ready to help you choose the right product for your project.