You may also like
SATCO Lighting S11214 4W, LED, 3000K, Clear, Double Contact Bayonet Base, 120-130V
4 Watt - LED - 3000K - Clear - Double Contact Bayonet base - 120-130 Volt
Manufacturer Resources
Spec Sheet
Product Specs
- Amps:
- 0.033-0.031A
- Avg Rated Hours:
- 25000
- Burning Position:
- Universal
- CCT Selectable:
- No
- DLC Approved:
- No
- Dimmable:
- Yes
- Enclosure Rating:
- Enclosed Rated Lamp
- FCC Compliant:
- Yes
- Lamp Filament:
- LED
- Lamp Shape:
- T4
- Lens Finish:
- Clear
- Lensed:
- Yes
- Lumens:
- 480L
- Product Type:
- Miniature
- Three-Way:
- No
- Warranty:
- 3 Year Limited
- Product Group:
- Indoor Lighting
- Product Subgroup:
- Light Bulbs
- Bulb Base:
- Bayonet Double Contact
- Base Material:
- Plastic
- Incandescent Equivalent:
- 35W
- Location Rating:
- Damp
- CRI:
- 80
- Subcategory:
- LED
- Title 24 Compliant:
- Yes
- Bulb Type:
- LED
- Product Voltage:
- 120V-130V
- Beam Spread Angle:
- 360
- Light Temperature:
- 3000K
- Product Category:
- Light Bulbs
- Product Wattage:
- 4W
- Product Weight:
- 0.03 lb
- Product Material:
- Plastic
Satco Lighting S11214 – Frequently Asked Questions
1) Will the Satco S11214 LED replace a 35W incandescent bayonet lamp in an exit sign or stairwell fixture?
Yes. The S11214 is a 4 watt LED rated as a 35 watt incandescent equivalent, putting out 480 lumens at 3000K. It uses a double contact bayonet base and runs on 120-130 volts, so it drops into the same socket and line voltage as the incandescent it replaces. Rated life is 25,000 hours, which is the reason most property managers make the swap in hard to reach fixtures.
2) Is a double contact bayonet base the same as a single contact bayonet? Will the wrong one fit?
They are not interchangeable electrically. The S11214 uses a double contact bayonet base, which has two contact buttons on the bottom of the cap and, on most fixtures, offset pins on the sleeve so it will only seat one way. A single contact bayonet lamp has one center button. Pull the old lamp and count the contacts before you order a case of these.
3) Can I use this Satco 4W bayonet LED in a fully enclosed fixture?
Yes, it is an enclosed rated lamp, so sealed globes, vandal resistant housings, and jelly jar type fixtures are fair game. It also carries a damp location rating, which covers covered exteriors, stairwells, and bathrooms, but not direct exposure to rain or sprinkler spray.
4) Can this bulb be installed base up or sideways?
Burning position is universal, so base up, base down, or horizontal are all acceptable. That matters on stair nosing lights, sign cans, and marine style fixtures where the socket orientation is fixed.
5) Will the clear T4 lamp give me a visible filament look or even light in a sign?
The S11214 has a clear lens on a T4 shape with a 360 degree beam spread, so it throws light all the way around rather than in one direction. Clear glass means the light source itself stays visible and you will get some sparkle, which is what you want behind a prismatic sign lens but can be glarey in an open fixture with no shade.
6) How many of these 4W Satco bayonet LEDs can I put on one circuit?
Each lamp draws 0.033 to 0.031 amps at 120-130 volts, so the current per lamp is tiny and lamp count is rarely the limiting factor on a lighting branch circuit. If you are retrofitting a string of 35W incandescents, the amp draw drops by roughly a factor of ten, which is often enough to free up capacity on an overloaded legacy circuit.
7) Does this Satco LED meet California Title 24?
Yes, the S11214 is Title 24 compliant, and it is FCC compliant for RF emissions. It is not DLC listed, so if your utility rebate program requires a DLC qualified product this lamp will not qualify for it.
8) Is 3000K going to match the other bulbs in my building?
The S11214 is fixed at 3000K warm white with a CRI of 80, and it is not a color selectable lamp, so what you see is what every unit ships as. That is a good match alongside other 3000K LED lamps, but it will read noticeably warmer next to 4000K and noticeably cooler next to a 2700K incandescent.
9) Will this bayonet LED work in a three-way fixture?
No. The S11214 is not a three-way lamp, so it will not step through light levels on a three-way socket. For level control you would need to be on a dimmer instead, which this lamp does support.
10) Is the base on this Satco miniature LED metal or plastic?
The bayonet cap is plastic. In a fixture that has been running hot incandescents for years, check that the socket contacts are clean and not corroded before seating a plastic based lamp, since a poor contact is where heat builds up.
How fast can I get the Satco Lighting S11214 delivered?
Most orders ship the same day from our distribution partners, with quick delivery throughout the
continental
U.S.
Need it urgently? Contact Us for expedited shipping options.
Can I return it if it doesn’t work for me?
Yes—ZenSupply offers a hassle-free return policy. If the product isn’t the right fit,
reach out to our support team for a return authorization or setup a return by following our return instructions.
Does the Satco Lighting S11214 come with a warranty?
Absolutely. The Satco Lighting S11214 is backed by a manufacturer’s warranty.
For full warranty terms, check the product documentation or Contact Us.
How do I get technical support or installation help for the Satco Lighting S11214?
You can call, text, or email our expert support team for fast answers. We’re here to help with
product
selection,
installation tips, and troubleshooting. Contact Us
Why buy the Satco Lighting S11214 from ZenSupply?
ZenSupply makes it easy to get the commercial door hardware you need—fast shipping, expert support,
and
rewards on
every order.
Our team is always ready to help you choose the right product for your project.