SATCO Lighting S12442 12.5W A19 LED, 100W Replacement, Clear, Medium Base, 2700K, 120V, 4-Pack
12.5 Watt A19 LED - 100 Watt Replacement - Clear - Medium base - 2700K - 120 Volt - 4-Pack
Manufacturer Resources
Product Specs
- Amps:
- 0.104A
- Avg Rated Hours:
- 15000
- Burning Position:
- Universal
- CA Web Text:
- Lawful for sale
- CCT Selectable:
- No
- CRI:
- 90
- DLC Approved:
- No
- Dimmable:
- Yes
- Enclosure Rating:
- Open Rated Lamp
- FCC Compliant:
- Yes
- Lamp Base:
- Medium
- Lamp Filament:
- LED Filament
- Lamp Shape:
- A19
- Lens Finish:
- Clear
- Lumens:
- 1500L
- Operating Frequency:
- 60Hz
- Product Type:
- Type A
- Subcategory:
- LED
- Technology:
- LED
- Three-Way:
- No
- Warranty:
- 3 Year Limited - 4 hr per day
- Product Group:
- Indoor Lighting
- Product Subgroup:
- Light Bulbs
- Incandescent Equivalent:
- 100W
- Location Rating:
- Wet
- Base Material:
- Aluminum / Glass
- Location Indoor/ Outdoor:
- Indoor;Outdoor
- Product Voltage:
- 120V
- Beam Spread Angle:
- 320
- Light Temperature:
- 2700K
- Product Category:
- Light Bulbs
- Product Wattage:
- 12.5W
Satco Lighting S12442 – Frequently Asked Questions
1) Can the Satco S12442 A19 LED be used in an enclosed fixture?
No. The S12442 is an open rated lamp, so it should not go in a fully enclosed fixture. Heat trapped in an enclosure shortens LED life. It is wet location rated and approved for indoor or outdoor use, so open porch fixtures, post tops, and covered exterior sockets are fine as long as air can move around the lamp.
2) Will the 2700K color match the incandescent bulbs already in my building?
Yes. At 2700K this Satco A19 is the warm white that matches standard incandescent and halogen, so mixing it into a fixture or hallway alongside older lamps will not read cool or blue. It is a fixed color temperature, not a CCT-selectable lamp, so every bulb in the 4-pack burns the same warm tone with no switch to set. CRI is 90, which holds skin tones and finishes better than a typical builder-grade LED.
3) Does the Satco S12442 work on a dimmer?
It is a dimmable lamp on 120V, 60Hz line voltage. Older incandescent dimmers will often work but can flicker or drop out at the low end with a load this small, so on a multi-fixture job it is worth wiring one circuit first before you buy for the whole building.
4) Will a clear LED filament bulb look right in an exposed-bulb fixture?
That is exactly what this one is built for. The S12442 uses LED filament construction behind a clear lens in an aluminum and glass body, so you see the filament strands rather than a frosted dome. In a chandelier, sconce, or open pendant where the bulb is visible it reads like a traditional clear incandescent. If the fixture leaves the bulb bare at eye level and you want less glare, choose a frosted lamp instead.
5) Can I mount the Satco S12442 base-up in a recessed can or sideways in a sconce?
Any orientation. Burning position is universal, so base-up, base-down, or horizontal all work. Just remember it is open rated, which rules out a sealed recessed can with a lens cover.
6) How wide does the light spread from this A19 LED filament lamp?
320 degrees, which is close to the all-around throw of an incandescent A19 rather than the forward-throw pattern of a cheaper LED with a heat sink blocking the back. That matters in a table lamp, a shade, or an open ceiling fixture where light needs to go up as well as down.
7) Is this Satco LED a three-way bulb?
No. The S12442 is a single-output lamp, so in a three-way socket it will light at one level only rather than stepping through settings. For a three-way table lamp you need a lamp specifically built for it.
8) How long will these last before a maintenance tech has to go back up the ladder?
The S12442 is rated 15,000 average hours. On a common-area fixture running roughly 12 hours a day that is around three and a half years of service. It ships four bulbs to a pack, which suits stocking a cart for multi-fixture relamping.
9) Is the Satco S12442 legal to sell and install in California?
Yes, it is marked lawful for sale in California. It also carries FCC compliance, which is the relevant point if radio interference from LED drivers has been a problem in the building.
How fast can I get the Satco Lighting S12442 delivered?
Most orders ship the same day from our distribution partners, with quick delivery throughout the
continental
U.S.
Need it urgently? Contact Us for expedited shipping options.
Can I return it if it doesn’t work for me?
Yes—ZenSupply offers a hassle-free return policy. If the product isn’t the right fit,
reach out to our support team for a return authorization or setup a return by following our return instructions.
Does the Satco Lighting S12442 come with a warranty?
Absolutely. The Satco Lighting S12442 is backed by a manufacturer’s warranty.
For full warranty terms, check the product documentation or Contact Us.
How do I get technical support or installation help for the Satco Lighting S12442?
You can call, text, or email our expert support team for fast answers. We’re here to help with
product
selection,
installation tips, and troubleshooting. Contact Us
Why buy the Satco Lighting S12442 from ZenSupply?
ZenSupply makes it easy to get the commercial door hardware you need—fast shipping, expert support,
and
rewards on
every order.
Our team is always ready to help you choose the right product for your project.