Schaub 211020 4-1/2" Turno 4" Center to Center Cabinet Pull

The Schaub 211020 mounts on 4 inch center-to-center holes. Two other pulls share that drilling exactly: the Omnia 1968/102, a forged solid brass modern pull with 4 inch center-to-center spacing, and the Trimco 562 series drawer pull, which is offered in a 4 inch center-to-center option alongside 3-1/2 inch and 96mm. Both reuse the existing two holes, so no re-drilling of the door or drawer front is needed. The look differs: the 211020 is a rustic cast bronze design, while the Omnia 1968/102 is modern in style.

The Schaub 211020 is drilled at 4 inch center-to-center and will not land on 3 inch holes. The Trimco 553 series drawer pull is made at 3 inch center-to-center and drops onto that existing drilling. If the cabinets are at 3-1/2 inch instead, the Deltana SBP35 modern square bar pull is a 3-1/2 inch solid brass heavy-duty pull, and the Trimco 562 series also lists a 3-1/2 inch center-to-center option.

The Schaub 211020 Turno projects 1-3/8 inches off the face. If clearance in a tight galley or against an adjacent appliance is a concern, the Omnia 1969 and Omnia 1971 both project 1-3/16 inches and the Omnia 1970 projects 1-1/4 inches, all in forged solid brass. All three are modern in profile rather than the rustic cast bronze look of the Turno.

Projection is 1-3/8 inches off the face, measured from the door or drawer front to the outside of the grip. That is generous for a pull this short, so gloved hands clear it fine. Worth checking against inset doors or appliance panels that swing past adjacent trim.

Four: Black Bronze (BB), Light Bronze (LB), Natural Bronze (NB), and Polished White Bronze (PWB). The three bronze tones are the usual pairing for rustic and transitional cabinetry; Polished White Bronze is the brighter option if you are matching nickel-toned faucets and appliances rather than dark iron.

The 211020 belongs to Schaub's Turno collection, so it is meant to be specified alongside the rest of that family rather than as a one-off. When you are standardizing a full set of cabinets, order every piece in the same finish code (BB, LB, NB or PWB) since bronze finishes vary between collections and production runs.

The Turno is a rustic cast bronze pull. If the job calls for clean modern lines, the Omnia 1968/102 is a forged solid brass pull on the same 4 inch center-to-center spacing, so it drops into identical drilling. The Deltana SBP35 modern square bar pull is another solid brass option, and Orca's CK-12001 T-pull bar is a steel bar pull in satin nickel if you want the contemporary bar profile.

Not as a like-for-like swap. The Schaub 211020 is a two-post pull on 4 inch centers with #8-32 screws, so it needs two holes. The Orca Hardware Bachelor CK-15030 and CK-16030 round knobs and the Blackcomb CK-17025 square knob are single-post cabinet knobs and mount in one hole, which means the second existing hole would be left open. Knobs are worth considering only on new doors or where you are refacing. If you want a bar-style pull instead, the Orca CK-12001 T-pull bar in steel with a satin nickel finish is a pull rather than a knob.

The Schaub 211020 comes in Black Bronze, Light Bronze, Natural Bronze and Polished White Bronze over a cast bronze base in the rustic Turno profile. For a plainer modern shape in solid brass, the Omnia 1968/102 is a forged solid brass modern pull on the same 4 inch center-to-center drilling, and the Deltana SBP35 is a heavy-duty solid brass square bar pull at 3-1/2 inch centers. Both are straight-line designs rather than the textured rustic Turno form, and the 3-1/2 inch Deltana would require re-drilling if your holes are set at 4 inches.

Yes. Emtek carries the Schaub Collection, including the Emtek 8405 Select cabinet pulls and the Alexander, Art Deco and Bar cabinet pulls. Those keep you inside one brand's ordering and finish program while still giving you Schaub-designed profiles, which helps when a spec sheet already lists Emtek for the rest of the openings.

Yes, Schaub publishes a Proposition 65 warning for this pull, and the product description links to the manufacturer's product stewardship page where the warning language is posted. If you are supplying a California job and need the notice on file, that is the source to pull it from.

No. The Schaub 211020 is a cabinet pull, 4-1/2 inches overall on 4 inch centers. The SDC SP50 is a 50mm spindle used in door controls, not a cabinet pull, and it will not mount to a cabinet door or drawer front. For an actual pull substitute, look at the Omnia 1968/102 or the Trimco 562 series.