Schaub 211054 Avenue Cabinet Pull with 6" Center to Center and Standard Mounting

It's set up for 8/32 x 1 inch machine screws, the standard cabinet pull thread. A 1 inch screw covers typical 3/4 inch fronts with thread to spare. If you're mounting into a 1 inch or thicker slab front, or a front with an applied panel, you'll need longer 8-32 screws, the thread pitch is the same so any 8-32 machine screw threads into the pull.

Only if the existing holes are 6 inches apart. Pull spacing is not standard across builder hardware, 3 inch, 3-3/4 inch, 4 inch and 96mm are all common on older drawers, so measure hole center to hole center before you order a fleet. If your existing spacing is smaller, the Trimco 562 Series covers 3-1/2 inch, 4 inch and 96mm, and the Omnia 1968/102 is a 4 inch ctc solid brass option. Re-drilling to 6 inch works on a bare replacement front but leaves two filled holes on an existing one.

The Schaub 211054 Avenue pull is a traditional-style solid brass pull on 6 inch centers with a 7-5/8 inch overall length and 1-3/8 inch projection. The nearest cross-brand counterparts in the same solid brass pull class are Omnia's forged solid brass cabinet pulls - the 1969 series and the 1971 series both carry a 1-3/16 inch projection, and the 1970 series carries a 1-1/4 inch projection, so all three sit slightly tighter to the door face than the Avenue's 1-3/8 inch. Omnia describes those series as modern rather than traditional, so the profile reads differently even where the material matches.

The Schaub 211054 Avenue pull is fixed at 6 inch center to center with a 7-5/8 inch overall length, so it will not land on a 4 inch hole pattern without redrilling. For an existing 4 inch bore, the Omnia 1968/102 is a forged solid brass cabinet pull built on 4 inch center-to-center spacing. Shorter patterns are covered by the Trimco 553 series drawer pulls at 3 inch centers and the Trimco 562 series, which offers 3-1/2 inch, 4 inch, and 96mm center-to-center options; the Deltana SBP35 is a heavy-duty solid brass square bar pull at 3-1/2 inches.

Projection is 1-3/8 inches. That's a deep grip, enough for a full hand on a heavy drawer or a pantry door, but worth measuring if the cabinet sits in a walkway or beside an appliance door that swings past it. Inset and full-overlay doors both take it the same way since the projection is measured off the door face, not the frame.

Brass base material. That matters for a couple of reasons on a job: brass takes and holds the living finishes, and it won't pit the way plated zinc does in a kitchen or a bath. It's also why the unlacquered brass option is offered, that finish is meant to patina over time rather than stay bright.

Five: Matte Black (MB), Polished Nickel (PN), Unlacquered Brass (UNBR), Satin Brass (SB), and Vintage Brass (VB). If you're standardizing a building or matching a kitchen already underway, note that three of the five are brass tones that read differently, satin is a soft even brushed brass, vintage is darkened and antiqued, and unlacquered is raw and will change color with handling. Order a sample of the brass tones before committing a whole run.

The 211054 is the 6 inch center-to-center Avenue pull specifically. Avenue is a collection, so Schaub builds it in a range of center-to-center lengths plus a matching knob, and the smaller ctc sizes carry their own model numbers rather than being an option on this one. Spec the 6 inch for wide drawers and doors, then order the shorter Avenue ctc sizes by their own numbers for narrow drawers so the styling stays consistent across the run.

Different jobs. The Avenue 211054 is a traditional-style pull, a shaped post-and-grip form that suits raised panel and shaker doors and inset cabinetry. A round or square bar pull is the modern read, cleaner line, usually shallower projection. If the cabinetry is contemporary and flat slab, look at the Emtek Bar Cabinet Pull or the Deltana SBP35 square bar pull in solid brass instead. If you want traditional but a shorter grip, the Trimco 553 Series drawer pull runs 3 inch ctc.

Yes. Emtek sells the Schaub Collection under its own catalog, including the Emtek 8405 Select cabinet pulls and named patterns like Alexander and Art Deco. Those are the same design house, so if your spec or your buying agreement runs through Emtek rather than Schaub, that is where to look for an equivalent. The individual Emtek pattern will have its own center-to-center offering, so confirm the ctc you need on whichever pattern you pick.

The Schaub 211054 belongs to the Avenue collection and is catalogued as a traditional-style brass pull. For a plainer bar profile, Emtek's Bar cabinet pull is offered in the Schaub collection, so it comes from the same design family under Emtek's badge, and the Emtek SELECT 8405 cabinet pulls are also a Schaub-collection item. Orca Hardware's CK-12001 T-pull bar is a steel pull with a 2 inch bar width in satin nickel, which is a different base material from the Avenue's brass. Deltana's SBP35 is a modern square bar pull in solid brass if you want to stay in brass while dropping the traditional detailing.

The 211054 is a Schaub Avenue pull in brass, traditional styling, 6 inch centers. Emtek sells several Schaub-collection cabinet pulls that share that design lineage: the Alexander series, the Art Deco series, the Bar series, and the SELECT 8405, all listed as cabinet knob/pull function. Because the Emtek Schaub-collection items include knob/pull variants, they cover the knob positions on doors while the Avenue handles the 6 inch drawer runs, which is how a kitchen usually splits between knobs and long pulls.

No - a knob is not a drop-in for the 211054. The Avenue pull mounts on two 8/32 x 1 inch screws spaced 6 inches apart, while knobs such as the Orca Hardware Bachelor Collection round knob at 1-1/4 inch diameter, the Bachelor Collection round ring knob at 1-1/4 inch diameter, and the Blackcomb Collection square knob at 25mm are single-point cabinet knobs. Swapping to a knob leaves one of the two existing 6 inch bores exposed, so knobs suit new doors or positions where only one hole is drilled.

No. It's a standard-mount pull, two through-holes at 6 inch centers and 8-32 machine screws from the back of the door or drawer front. No backplate, no rosette, no special prep beyond drilling the two holes. All you need on site is a drill, the correct bit for an 8-32 screw shank, and a jig or template to keep the two holes level.

No. The Schaub 211054 Avenue is a cabinet pull - a brass grip mounted to a drawer or door face on 6 inch centers. The SDC SP50 is a 50mm spindle used in door control applications, so it is an internal drive component rather than anything a hand grips on a cabinet. The two are not interchangeable in either direction.