Schaub 213 8" Center to Center Northport Round Cabinet Pull

Yes, the Northport 213 is drilled on 8 inch center-to-center spacing, so it drops onto cabinet doors or drawer fronts already bored at 8 inches without new holes. Overall length is 9 inches, so it overhangs the mounting holes by about half an inch at each end. If your existing holes are on a different spacing, the 213 will not line up, and you would need a different center-to-center size in the Northport collection.

The Omnia 1970 is a modern cabinet pull built in forged solid brass with a 1-1/4 inch projection, matching the 1-1/4 inch projection of the Schaub 213 Northport round pull. The Schaub 213 uses a zinc base material, so the Omnia 1970 is the option when a forged solid brass body is specified for the run. Confirm the center-to-center spacing on the Omnia against the 8 inch center-to-center of the Schaub 213 before drilling, since the projection match does not imply a bore match.

The Northport 213 uses 8/32 threaded screws, which is the standard cabinet hardware machine screw thread. That matters if your doors or drawer fronts are thicker than usual, or if you are mounting through a shaker frame plus a backing panel: you buy longer 8/32 screws to suit the thickness rather than a different pull.

Projection is 1-1/4 inches, measured from the door face to the back of the bar. That is enough clearance for a gloved hand, and it is the number to check where a drawer sits next to a wall return or an appliance panel, because the pull will be the first thing that hits.

Zinc is the base material on the Northport 213, finished in one of eight platings. That is a different build from forged solid brass pulls like the Omnia 1970, which is worth knowing if you are specifying for a heavy-use commercial or multi-family kitchen where residents pull hard on 9 inch appliance-scale hardware.

Eight finishes cover the Northport 213: Satin Nickel, Polished Chrome, Ancient Bronze, Brushed Bronze, Brushed Nickel, Matte Black, Polished Nickel, and Signature Satin Brass. Both nickel tones and both bronze tones are offered, so if you are matching existing hardware, pin down whether the fleet is brushed or polished before you order, the two do not read the same across a run of cabinets.

The Northport 213 is a transitional round bar pull, so a coordinating program is straightforward. Emtek carries the Schaub Collection under its SELECT line, model 8405, which includes cabinet knobs and pulls in the same design family. For a plain round knob in a similar transitional look, the Orca Hardware Bachelor Collection CK-15030 is a 1-1/4 inch diameter round cabinet knob, matching the 213's bar diameter.

Zinc with a plated finish is the construction on the Northport 213, which suits interior cabinetry. For exterior or wet locations, a forged solid brass pull holds up better, and the Omnia 1968, 1969, 1970 and 1971 Series are forged solid brass cabinet pulls if that is the condition you are buying for.

The Orca Hardware CK-12001 is a T-pull bar in steel with a 2 inch bar width, offered in satin nickel. The Schaub 213 Northport uses a zinc base material and is available in Satin Nickel, Brushed Nickel, Polished Nickel, Polished Chrome, Matte Black, Ancient Bronze, Brushed Bronze, and Signature Satin Brass. If the finish schedule is satin nickel and you want a steel body for repeat-tenant turns, the CK-12001 covers that; the Schaub 213 covers the wider finish range across a mixed unit.

The round bar measures 1-1/4 inches as the base dimension. Combined with the 1-1/4 inch projection, that gives a full-hand grip rather than a fingertip pull, which is why the 213 works on heavy appliance panels and large pantry doors.