Schaub 317 6-5/16" Center to Center Positano Clear Cabinet Pull

It takes M4 metric machine screws, not the 8-32 standard used on most US cabinet hardware. That matters two ways: if you are mixing this pull with older American pulls in the same kitchen you will have two screw types on the job, and if your drawer fronts are thick or have applied panels you need longer M4 screws than whatever ships in the bag.

The Schaub 317 Positano is a contemporary-style cabinet pull with a zinc base material. If solid brass is the requirement, the Omnia 1968/102 is a modern cabinet pull in forged solid brass with 4 inch center-to-center spacing, and the Omnia 1970 is a forged solid brass modern pull with a 1-1/4 inch projection. Note the spacing difference: the Schaub 317 drills at 160 mm centers, so the Omnia 1968/102 at 4 inch centers will not land on the same holes.

The Schaub 317 Positano is a zinc-base decorative pull built around the Positano collection styling. For commercial casework where a plain heavy-duty bar is preferred, the Deltana SBP35 is a modern square bar pull at 3-1/2 inches described as heavy-duty solid brass, and the Orca Hardware CK-12001 is a T-pull bar in steel with a 2 inch bar width in satin nickel. Trimco also offers utilitarian drawer pulls: the 553 Series at 3 inch center-to-center and the 562 Series with 3-1/2 inch, 4 inch and 96 mm center-to-center options.

No. The Schaub 317 Positano drills at 160 mm center-to-center and uses M-4 metric screws. The Trimco 553 Series is 3 inch center-to-center and the 562 Series offers 3-1/2 inch, 4 inch and 96 mm, while the Omnia 1968/102 is 4 inch center-to-center. None of those match 160 mm, so swapping means new holes or a backplate.

Projection is 1 inch, with a 1/2 inch base dimension where it meets the door or drawer front. One inch of clearance is enough for a gloved hand and keeps the pull from crowding a run of drawers in a tight galley or a corner where a drawer swings past an adjacent cabinet.

Six combinations, pairing a metal finish with a clear or smoke acrylic insert: Satin Nickel/Clear, Satin Nickel/Smoke, Polished Chrome/Clear, Polished Chrome/Smoke, Signature Satin Brass/Clear, and Signature Satin Brass/Smoke. Clear reads brighter and nearly disappears against a light front; smoke gives a darker, greyed insert that shows more against white or pale cabinetry.

The Positano 317 is only offered at 160mm center-to-center, so for short drawers you need a different family. For a contemporary look in smaller spacings, the Trimco 553 Series drawer pull is 3 inch center-to-center and the Trimco 562 Series comes in 3-1/2 inch, 4 inch, and 96mm. The Omnia 1968/102 is 4 inch center-to-center in forged solid brass.

The Schaub 317 Positano is sized at 160 mm center-to-center with a 6-5/8 inch overall length, which is long for a narrow drawer front. Emtek sells cabinet pulls under the Schaub Collection in several series, including the Emtek 8405 Select, the Alexander, the Art Deco and the Bar cabinet pulls, all catalogued as cabinet knob/pull. Those give you the same design family in shorter formats. For a true knob instead of a pull, the Orca Hardware CK-15030 Bachelor round cabinet knob is 1-1/4 inch in diameter.

The Schaub 317 Positano projects 1 inch off the door face. Among modern comparables, the Omnia 1970 carries a 1-1/4 inch projection, while the Omnia 1969 and Omnia 1971 are both listed at 1-3/16 inch projection. All three sit slightly further off the face than the 317, which matters where a drawer sits close to an adjacent appliance or wall return.

It works on both, but a 6-5/8 inch pull on a narrow upper door can look oversized. A common approach is to run the 317 on drawer banks and use a knob on the doors. For that, the Orca Hardware Bachelor Collection round knob at 1-1/4 inch diameter or the Blackcomb 25mm square knob are contemporary shapes that sit alongside it.

It is a zinc-body decorative pull with an acrylic insert, aimed at contemporary residential cabinetry. For heavy turnover units where pulls take abuse and get replaced in bulk, a plain metal bar is the safer standardization choice: the Deltana SBP35 heavy-duty solid brass square bar pull or the Orca Hardware CK-12001 steel T-pull bar in satin nickel are both built for that kind of service.

Yes. Schaub publishes a Proposition 65 warning for this product through its product stewardship page, which matters if you are supplying into California or documenting materials for a commercial job file.

No. The Schaub 317 Positano is a cabinet pull mounting to a drawer or door face at 160 mm centers. The SDC SP50 is a 50 mm spindle catalogued under door controls, an internal trim component rather than a graspable cabinet pull. If you are looking for a contemporary pull instead, the Omnia 1969 and Omnia 1971 modern forged solid brass pulls are closer matches.