Schaub 372 288mm Center to Center Regatta Cabinet Pull

It uses M4 metric machine screws. That matters on a retrofit: a lot of North American cabinet hardware runs 8-32, so if you are swapping in the Regatta over existing pulls, the old screws will not thread into it. Use the M4 screws that come with the pull.

The Schaub 372 Regatta pull uses a zinc base material. If the specification calls for solid brass, the Omnia 1968/102 modern cabinet pull is forged solid brass with 4 inch center-to-center spacing, and the Omnia 1970 modern cabinet pull is forged solid brass with a 1-1/4 inch projection. Note the center-to-center difference: the Schaub 372 is drilled at 288 mm, so an Omnia at 4 inch spacing will not land on the same holes and drawer fronts would need to be re-bored.

The Schaub 372 Regatta is a long appliance-scale pull at 348 mm overall on 288 mm centers, which needs a wide drawer front. For narrow drawers, the Trimco 553 series drawer pulls are drilled at 3 inch center-to-center, and the Trimco 562 series offers 3-1/2 inch, 4 inch, and 96 mm center-to-center options. The Deltana SBP35 modern square bar pull is a 3-1/2 inch solid brass heavy-duty pull. Any of these will fit a drawer front that cannot carry a 348 mm pull.

Projection is 1-1/8 inches from the face of the door or drawer. That is enough finger clearance for a gloved hand, and it is worth measuring against anything adjacent, a wall return, an appliance panel, or a drawer that swings past a corner cabinet.

Four: Satin Nickel, Polished Chrome, Matte Black with Satin Nickel, and Matte Black with Chrome. The two Matte Black options are two-tone, black body with bright or satin metal accent, so if you are matching a full kitchen of single-tone hardware, stay with straight Satin Nickel or Polished Chrome.

Regatta is a contemporary Schaub collection. Emtek sells the Schaub Collection under its own catalog, including the Emtek 8405 SELECT cabinet pulls and the Bar, Alexander and Art Deco cabinet pulls, so you can pull knobs and shorter pulls from the same design family when the Regatta profile is not made in the size you need.

Yes, and it is common to run long pulls on drawers with knobs on doors. The Schaub 372 Regatta is a contemporary-style pull; for matching knobs the Orca Hardware Bachelor Collection offers a round cabinet knob at 1-1/4 inch diameter and a round ring knob at 1-1/4 inch diameter, and the Blackcomb Collection offers a square knob at 25 mm diameter. Knobs use a single hole, so no center-to-center match to the Schaub 372's 288 mm spacing is required.

They are related but not the same part. The Schaub 372 is from the Regatta collection at 288 mm center-to-center with M-4 metric screws. Emtek carries its own Schaub Collection pulls under separate series names, including the Emtek 8405 Select cabinet pulls, the Alexander series, the Art Deco series, and the Bar series, each catalogued as a cabinet knob/pull. If you are matching an existing Regatta installation, order the Schaub 372 rather than an Emtek series part.

The Schaub 372 Regatta projects 1-1/8 inch off the face. For more knuckle clearance, the Omnia 1970 modern cabinet pull has a 1-1/4 inch projection, and the Omnia 1969 and Omnia 1971 modern cabinet pulls each have a 1-3/16 inch projection, all in forged solid brass. Confirm center-to-center spacing separately, since the Schaub 372 is drilled at 288 mm.

The Schaub 372 Regatta pull is offered in two-tone combinations, Matte Black/Satin Nickel and Matte Black/Chrome, alongside single-finish Satin Nickel and Polished Chrome. Among the alternatives, the Orca Hardware CK-12001 T-pull bar is a single satin nickel finish, so if the design calls for a two-tone pull the Schaub 372 is the one that carries it.

Yes. Schaub publishes a Proposition 65 warning covering this pull, and the manufacturer's product stewardship page carries the detail. If you are specifying into a California project, flag it in your submittal package.