Schaub 373 320mm Center to Center Regatta Cabinet Pull

The Schaub 373 Regatta is a contemporary-style cabinet pull with a zinc base material. If solid brass construction is the requirement, the Omnia 1969 and Omnia 1970 are modern cabinet pulls of forged solid brass, with the 1969 at 1-3/16 inch projection and the 1970 at 1-1/4 inch projection, against the 1-1/8 inch projection of the Regatta. The Omnia pulls are forged brass bar pulls in a modern idiom; the Regatta is a zinc pull in the Regatta collection. Confirm the center-to-center spacing you need on the Omnia side, since the Regatta is a 320 mm center-to-center pull.

Projection is 1-1/8 inches from the door face to the back of the grip, which gives full four-finger clearance and works in front of an appliance panel or in a tight galley run where a deeper pull would catch a hip. The post base measures 3/8, so the grip itself sits clear of the door for cleaning behind it.

Base material is zinc, a die-cast body rather than forged brass. For apartment turns and spec kitchens that is normally the point, it holds a plated finish at a lower cost per opening. If you want forged solid brass on a high-traffic commercial or hospitality job, the Omnia 1968/102 and Omnia 1970 modern cabinet pulls are forged solid brass alternatives, and the Deltana SBP35 square bar pull is solid brass heavy-duty.

Four finishes: Satin Nickel, Polished Chrome, Matte Black with Satin Nickel, and Matte Black with Chrome. The last two are genuine two-tone, black grip against a bright or satin post, which is the usual way this pull gets matched to mixed-metal faucets and lighting in a kitchen. If every pull in the run has to read identically, order the whole run in one finish code, plating lots vary.

The 373 is a Regatta collection pull in the contemporary style line, so it shares the Regatta grip profile with the rest of that collection. Matching across a kitchen means matching collection and finish, then choosing the center-to-center that suits each door or drawer width, this one is the 320 mm size.

A 320 mm pull like the Schaub 373 Regatta is the choice where the door or drawer is wide and gets pulled under load, a trash pullout, a pantry, a deep pot drawer, because the grip spreads the pull across two fixings and gives a full hand. Knobs suit small upper doors and narrow fronts and only need one hole. If you want knobs on the uppers to balance long pulls below, the Orca Hardware Bachelor Collection round knob is 1-1/4 inch diameter and the Blackcomb square knob is 25mm.

Yes, that is a common split: long pulls on wide drawer fronts, knobs on small doors. The Schaub 373 Regatta is a 320 mm center-to-center pull with 1-1/8 inch projection. On the knob side, the Orca Hardware Bachelor Collection offers a round cabinet knob at 1-1/4 inch diameter under CK-15030 and a round ring knob at 1-1/4 inch diameter under CK-16030, and the Blackcomb Collection CK-17025 is a square knob at 25 mm diameter. Knobs take a single hole rather than the two-hole pattern the Regatta requires, so decide the split before drilling.

The Orca Hardware CK-12001 is a T-pull bar in steel with a 2 inch bar width, supplied in satin nickel, and is a plainer piece of hardware than the Regatta, which is a contemporary zinc pull at 320 mm center to center in a decorative collection. The Regatta is offered in satin nickel, polished chrome, matte black with satin nickel, and matte black with chrome, so if the finish is what drives the specification the Regatta covers more ground; if the run is purely functional the steel T-pull is the simpler part.

The Schaub 373 Regatta projects 1-1/8 inch off the face of the cabinet. The Omnia 1971 is a modern cabinet pull of forged solid brass with a 1-3/16 inch projection, and the Omnia 1970 carries a 1-1/4 inch projection. If gloved hands or a heavy drawer make grip clearance the deciding factor, the Omnia pulls stand further off the front; if the drawer sits next to an appliance or an adjacent door swing where clearance is tight, the shallower Regatta projection is the one to check against.

Yes. The 373 Regatta is a two-post pull on 320 mm centers with no top or bottom to the grip, so it mounts vertically on a tall door or horizontally on a drawer using the same drilling. On a vertical run, mark both holes off a single plumb line, 320 mm apart, and keep the projection of 1-1/8 inches in mind where the door swings past a wall return.

The 373 Regatta ships with M4 metric machine screws for the two posts. That is all the hardware the pull needs on a standard cabinet front. What is not included is anything for filling or re-drilling old holes, so if your existing bore is not 320 mm center-to-center, plan on plugs and a drilling jig as part of the job.

No. The SDC SP50 is a 50 mm spindle, a door control component, not a cabinet pull. The Schaub 373 Regatta is a cabinet pull, 320 mm center to center and 380 mm overall, that mounts through the cabinet front on M-4 metric screws. The two parts do not do the same job and there is no mounting relationship between them.