Schaub 371 224mm Center to Center Regatta Cabinet Pull

Only if the existing pulls are on 224 mm centers. That is a metric spacing common on European and contemporary cabinetry; if the boxes were built to US spacing you are more likely to find 3 inch, 3-1/2 inch, 4 inch or 96 mm patterns, none of which line up with 224 mm. Measure center of hole to center of hole on one existing pull before ordering. Where the openings are on 3 inch or 3-1/2 inch centers, Trimco's 553 Series (3 inch ctc) and 562 Series (3-1/2 inch, 4 inch and 96 mm ctc) drawer pulls cover those patterns.

The Schaub 371 Regatta is a contemporary-style cabinet pull with a zinc base material. If a forged solid brass body is required by the spec, the Omnia 1968/102 is a modern cabinet pull in forged solid brass with 4 inch center-to-center spacing, and the Omnia 1970 is a modern forged solid brass pull with a 1-1/4 inch projection. Note the mounting spacing differs: the 371 drills at 224 mm center-to-center, so switching to the 1968/102 at 4 inch centers means a different hole pattern in the door or drawer front.

Emtek sells the Schaub Collection under its own part numbers, so a job written to Emtek can be filled from that range: the Emtek 8405 Select cabinet pull, the Emtek Alexander cabinet pull, the Emtek Art Deco cabinet pull, and the Emtek Bar cabinet pull are all Schaub Collection cabinet knob/pull items. Those are separate series from the Schaub 371 Regatta, so confirm the center-to-center spacing on the Emtek series you pick against the 224 mm pattern the 371 uses before the fronts are drilled.

They are not a drop-in. The Trimco 553 Series drawer pulls are 3 inch center-to-center and the Trimco 562 Series comes in 3-1/2 inch, 4 inch, and 96 mm center-to-center options. The Schaub 371 Regatta drills at 224 mm center-to-center, so none of those Trimco spacings will pick up existing 371 holes. The Trimco pulls suit a shorter drawer front or a commercial casework spec; the 371 is a contemporary-style pull at a 284 mm overall length.

M4 metric machine screws, which is the standard cabinet hardware thread. Note that it is metric rather than the 8-32 thread common on domestic pulls, so if you are mixing this in with older US-made hardware, keep the supplied screws with the pull. Drawer fronts and door stiles vary in thickness, so check that the screw length you have on hand reaches through the front and still catches the pull.

Four: Satin Nickel, Polished Chrome, Matte Black with Satin Nickel, and Matte Black with Chrome. The two Matte Black options are two-tone, so if you are matching a kitchen that is already all one metal, Satin Nickel or Polished Chrome are the single-finish choices. For a multi-unit or spec job, order the whole run at once so the finish comes from the same production batch.

The 371 Regatta is the 224 mm center-to-center size, which suits wide drawers and full-height pantry or appliance doors. For smaller drawers and doors in the same kitchen, stay inside the Schaub Regatta collection at a shorter center-to-center rather than mixing collections, since the grip profile is what reads across the run. Emtek also carries the Schaub Collection under its SELECT cabinet pull line if you want the same design house across a broader hardware package.

The Schaub 371 Regatta carries a 1-1/8 inch projection. Among comparable modern pulls, the Omnia 1969 and the Omnia 1971 are both forged solid brass pulls with a 1-3/16 inch projection, and the Omnia 1970 sits at 1-1/4 inch, so those stand off the face slightly further rather than less. For a run where knuckle clearance is the constraint, a knob is the other direction entirely: the Orca Hardware Blackcomb CK-17025 is a square cabinet knob at 25 mm diameter, and the Bachelor CK-15030 is a round cabinet knob at 1-1/4 inch diameter, both single-hole mounts rather than a two-hole 224 mm pattern.

For a plainer look on utility runs, the Deltana SBP35 is a modern square bar pull at 3-1/2 inch, heavy-duty, in solid brass, and the Orca Hardware CK-12001 is a T-pull bar with a 2 inch bar width in steel, supplied in satin nickel. The Schaub 371 Regatta itself is a 224 mm center-to-center pull with a 284 mm overall length, so both of those bar pulls are considerably shorter across and will not land on the same two holes.

The Schaub 371 Regatta is offered in Matte Black/Satin Nickel and Matte Black/Chrome, alongside single-tone Satin Nickel and Polished Chrome. Among comparable modern pulls, the Orca Hardware CK-12001 T-pull bar is a steel bar pull supplied in satin nickel, a single-tone finish. If the design calls for a mixed-metal pull on a 224 mm hole pattern, the 371 two-tone finishes cover it directly.

You can, and it removes the hole-spacing variable entirely. The Orca Hardware Bachelor CK-15030 is a round cabinet knob at 1-1/4 inch diameter, the Bachelor CK-16030 is a round ring cabinet knob at 1-1/4 inch diameter, and the Blackcomb CK-17025 is a square cabinet knob at 25 mm diameter. Each is a single-hole mount, so it does not need to match the 224 mm two-hole pattern the Schaub 371 Regatta uses, which matters when drawer fronts across a portfolio were drilled to different spacings.

Regatta is a contemporary pull, not a plain round bar. If what you actually want is a straight tube bar pull, the Orca CK-12001 T-pull bar in steel or the Deltana SBP35 square bar pull are that shape instead. If you are pulling together a whole kitchen, the Emtek Bar, Alexander and Art Deco cabinet pulls from the Schaub Collection give you other profiles to compare against before you settle.

It works on both, but 224 mm is a long pull for a door. Common practice is pulls on drawers and either a shorter pull or a knob on the doors. If you want knobs to carry the run, Orca's Bachelor Collection round knob and round ring knob are both 1-1/4 inch diameter, and the Blackcomb square knob is 25 mm. Knobs mount on a single hole, so plan the boring before the fronts are drilled.

The Schaub 371 Regatta uses an M-4 metric thread screw size, which is the metric machine screw standard rather than the 8-32 pattern common on domestic hardware. Comparable pulls such as the Omnia 1969 and Omnia 1971, both forged solid brass modern pulls with a 1-3/16 inch projection, are their own series and should be ordered with their own screws rather than assuming loose stock will thread the 371. If you are mixing series across a job, keep the screws with their pulls.

No. The SDC SP50 is a 50 mm spindle, a door controls item, not a cabinet pull. The Schaub 371 Regatta is a cabinet pull at 224 mm center-to-center with a 284 mm overall length. If a spindle turned up on the same order as cabinet hardware it is for a lockset, not for a drawer or door front.