Schaub 476 6" Center to Center Haniburton Cabinet Pull

The 476 takes 8/32 x 1 inch machine screws. A 1 inch screw through a 3/4 inch drawer front leaves about 1/4 inch of thread into the post, which is enough. If you are going through a thicker slab front or a front plus an applied panel, you will need longer 8-32 screws.

The Omnia 1969 Modern Cabinet Pull is forged solid brass with a 1-3/16 inch projection, close to the 1-3/8 inch projection of the Schaub 476 Haniburton pull, which is also solid brass. The Omnia 1971 is another forged solid brass pull at 1-3/16 inch projection, and the Omnia 1970 runs 1-1/4 inch projection. The visual difference is styling: the Haniburton is a transitional design, while the Omnia 1969, 1970 and 1971 are modern series pulls.

The Schaub 476 Haniburton pull is drilled at 6 inch center-to-center, so it will not drop into shorter existing holes. For narrower spacing, the Omnia 1968/102 is a forged solid brass pull at 4 inch center-to-center, the Trimco 562 Series drawer pulls are offered in 3-1/2 inch, 4 inch and 96mm center-to-center, the Trimco 553 Series is 3 inch center-to-center, and the Deltana SBP35 square bar pull is 3-1/2 inch in solid brass.

Projection is 1-3/8 inches off the face of the door or drawer, measured to the outside of the grip, so there is room to hook a full hand rather than fingertips. That also matters for clearance: in a corner or beside a wall, allow 1-3/8 inches plus knuckle room before the pull stands proud of anything adjacent.

Solid brass base material. That is why it is offered in Unlacquered Brass, which is a living finish that will patina with handling rather than a clear-coated look, alongside the sealed finishes.

Six: Satin Nickel (SN), Polished Nickel (PN), Polished Chrome (PC), Matte Black (MB), Satin Brass (SB), and Unlacquered Brass (UNBR). For a kitchen where the faucet is polished chrome, PC is the match; UNBR is the one that will change color over time, so do not mix it with a sealed brass on the same run of cabinets.

The Haniburton is a transitional profile. For a straighter modern look in solid brass, the Omnia 1968 series is a forged solid brass pull offered in 4 inch centers, and the Deltana SBP series is a square bar pull in solid brass. Emtek's SELECT cabinet pull line, which carries the Schaub collection, is another route if you want to mix bar lengths across a kitchen.

Only where a single hole is acceptable. The Schaub 476 Haniburton is a two-hole pull on 6 inch centers with 8/32 x 1 inch screws. Knobs such as the Orca Hardware CK-15030 round knob at 1-1/4 inch diameter, the CK-16030 round ring knob at 1-1/4 inch diameter, and the CK-17025 square knob at 25mm diameter mount on a single fastener, so swapping to them leaves the second existing bore exposed.

The Schaub 476 Haniburton is a solid brass transitional pull. If you want a steel body instead, the Orca Hardware CK-12001 T-pull bar is steel with a 2 inch bar width in satin nickel. If you prefer to stay in brass, the Deltana SBP35 is described as a heavy-duty solid brass square bar pull. Both change the look from the Haniburton profile to a bar style.

The Schaub 476 Haniburton stands off the door 1-3/8 inch. Among comparable solid brass pulls, the Omnia 1969 and Omnia 1971 project 1-3/16 inch and the Omnia 1970 projects 1-1/4 inch, so all three sit slightly closer to the face of the cabinet - useful where an adjacent wall, appliance or door swing is tight.

The base dimension is 5/8 inch, so each post foot is a 5/8 inch footprint on the face. That will hide a standard screw hole but not a mis-drilled or plugged hole any bigger than that.

The 476 is a pull only. For knobs on the uppers, Orca Hardware's Bachelor Collection round knob is 1-1/4 inch diameter and the Blackcomb square knob is 25mm, both available in cabinet knob form. Match the finish family rather than the collection, since those are different lines from the Haniburton.

The Trimco 553 Series drawer pulls are 3 inch center-to-center and the Trimco 562 Series comes in 3-1/2 inch, 4 inch and 96mm center-to-center, all shorter than the 6 inch center-to-center Schaub 476 Haniburton pull. They will fit narrow drawer fronts where the 6-5/8 inch overall length of the 476 is too long, but they will not repeat the Haniburton transitional profile, so expect a visible difference between doors and drawers.