Schaub 475 5" Center to Center Haniburton Cabinet Pull

The Haniburton 475 uses #8-32 x 1 inch machine screws, which is the standard cabinet hardware thread. One inch covers typical 3/4 inch fronts with room for the post. If you are mounting through a thicker slab front, a drawer box face plus a false front, or adding a backplate, you will need longer #8-32 screws.

The Schaub 475 Haniburton stands 1-3/8 inch off the door face. If the opening cannot give up that much clearance, the Omnia 1969 and Omnia 1971 both project 1-3/16 inch, and the Omnia 1970 projects 1-1/4 inch, all in forged solid brass. Any of the three brings the grip closer to the face than the 475 while keeping the same brass construction.

Projection is 1-3/8 inch, measured from the face of the door or drawer to the outside of the grip. That is a generous hand clearance, which matters if you have inset cabinetry near a corner or an adjacent appliance panel where the pull could collide when the door swings.

Six finishes: Satin Nickel, Polished Chrome, Matte Black, Polished Nickel, Satin Brass, and Unlacquered Brass. The Unlacquered Brass has no protective coating, so it will patina with handling over time. If you want brass that holds its as-shipped look, specify Satin Brass instead.

The Haniburton is a Schaub collection, and collections run across multiple center-to-center sizes and matching knobs, so staying inside Haniburton is how you keep the profile consistent between drawers and doors. If you are matching across brands instead, Trimco 553 Series drawer pulls run 3 inch center-to-center and the 562 Series offers 3-1/2 inch, 4 inch, and 96mm options.

The Schaub 475 Haniburton is bored at 5 inch center-to-center, which suits wider drawer fronts. For narrower fronts, the Trimco 553 series drawer pulls are 3 inch center-to-center and the Trimco 562 series offers 3-1/2 inch, 4 inch, and 96mm center-to-center. Those give you shorter bore spacing on the same drawer application; confirm the bore layout before drilling since none of them match the 475 hole pattern.

The Schaub 475 Haniburton is solid brass. If you want a steel pull instead, the Orca Hardware CK-12001 T-pull bar is steel with a 2 inch bar width in satin nickel. The Schaub 475 is offered in satin nickel as well, so the finish family can be matched across a job, but the base materials differ and the CK-12001 is a bar-style pull rather than the transitional Haniburton profile.

It is a transitional design, which is the middle ground between traditional and contemporary. It reads correctly on shaker doors, flat-slab fronts, and painted inset cabinetry alike. If you want something overtly modern, the Omnia 1968 and 1969 Series are modern-styled forged brass pulls; for a period look, the Emtek Art Deco Cabinet Pull in the Schaub Collection is the period-specific option.

The Emtek SELECT 8405, Alexander, Bar, and Art Deco cabinet pulls are all catalogued under the Schaub Collection, so they are the same design house in Emtek packaging. Haniburton is the Schaub-branded line. Choose on profile: Bar for a straight tube grip, Alexander and Art Deco for decorative profiles, Haniburton for the transitional shape in solid brass with 1-3/8 inch projection.

Yes. Schaub publishes a Proposition 65 warning covering this pull, linked from their product stewardship page. Brass hardware commonly carries one because of lead content in the alloy. If you are specifying for a California project, pull that notice for your submittal file.

Yes, pulls and knobs are commonly mixed, with pulls on drawers and knobs on doors. The Schaub 475 Haniburton is a two-hole cabinet pull at 5 inch center-to-center using #8-32 x 1 screws. Single-hole knob options include the Orca Hardware CK-15030 round cabinet knob at 1-1/4 inch diameter, the CK-16030 round ring knob at 1-1/4 inch diameter, and the CK-17025 square knob at 25mm diameter. Knobs use one bore rather than the pull's two, so plan the drilling accordingly.