Schaub 478 8" Center to Center Haniburton Cabinet Pull

The 478 uses 8/32 machine screws at 1 inch long. That covers a standard 3/4 inch drawer front or door with thread left to engage the post. If you are mounting through a thicker slab front, a false front plus a box front, or a drawer front with an applied panel, the 1 inch screw runs short and you will need longer 8-32 machine screws in the same thread.

The Schaub 478 Haniburton projects 1-1/2 inches off the face. The Omnia 1970 is a forged solid brass cabinet pull with a 1-1/4 inch projection, and the Omnia 1969 and Omnia 1971 both carry a 1-3/16 inch projection. In a galley kitchen or a corridor of base cabinets where a deep pull catches hips and tool belts, the shallower Omnia projections buy back a quarter inch or so of clearance; the 478 gives a fuller grip for a gloved hand.

The Schaub 478 Haniburton spans 8-3/4 inches overall on 8 inch centers, which needs a wide drawer or a tall door to look right. For narrow fronts, the Trimco 553 Series drawer pulls are 3 inch center-to-center, the Trimco 562 Series offers 3-1/2 inch, 4 inch, and 96mm center-to-center, and the Deltana SBP35 is a heavy-duty solid brass square bar pull at 3-1/2 inches. Any of those drill inside the width of a standard 12 inch drawer box front where the 478 would run edge to edge.

No. The Orca CK-15030 and CK-16030 are round cabinet knobs at 1-1/4 inch diameter and the Orca CK-17025 is a square cabinet knob at 25mm diameter. A knob mounts on a single screw hole, while the Schaub 478 Haniburton is a cabinet pull on 8 inch centers using two 8/32 x 1 inch screws. Swapping a knob in for the 478 leaves an unused hole in the front, so knobs are a fresh-drill decision, not a retrofit.

Projection is 1-1/2 inches, with a 3/4 inch base. That is a generous grip, enough to get a full hand behind on a heavy pot drawer, but it is also 1-1/2 inches into the walkway. In a galley kitchen or a tight butler's pantry where doors face each other, measure the aisle before committing to a run of these.

Six: Satin Nickel, Polished Chrome, Matte Black, Polished Nickel, Satin Brass, and Unlacquered Brass. Unlacquered Brass is the one to think twice about on a rental or a commercial job. It has no protective coating, so it darkens with handling and every unit ages differently. For a property manager who wants twenty kitchens to match in year five, Satin Nickel or Matte Black holds its appearance.

At 8 inches on center the 478 is sized for large doors, wide deep drawers, and appliance panels, not for small vanity drawers where it would run wall to wall. For narrower drawers, shorter pulls in the same category include the Trimco 553 Series at 3 inch centers and the Trimco 562 Series in 3-1/2 inch, 4 inch, and 96mm centers, or the Omnia 1968/102 at 4 inch centers. A common approach is running the 478 on the big drawers and a shorter pull on the small ones.

The 478 is built as a cabinet pull, and its 8 inch centers and 1-1/2 inch projection suit a panel front. The limit is the screw: it ships with 8/32 x 1 inch machine screws, which are sized for roughly a 3/4 inch panel. Appliance panels are frequently thicker or require through-bolting into a factory-drilled bracket, so plan on sourcing longer 8-32 machine screws to suit your actual panel thickness.

The Orca Hardware CK-12001 is a T-pull bar in steel with a 2 inch bar width in satin nickel. The Schaub 478 Haniburton is solid brass with a 3/4 inch base dimension and is offered in satin nickel, polished chrome, matte black, polished nickel, satin brass, and unlacquered brass. For a property manager standardizing a maintenance shop or a back-of-house run, the steel Orca bar is a different material class; for a unit turn where the rest of the kitchen is brass hardware, the 478 finish range covers the match, including unlacquered brass that will patina over time.

Yes. Emtek sells the Schaub Collection under its own part numbers, including the Emtek 8405 Select cabinet pulls, the Emtek Alexander cabinet pull, the Emtek Art Deco cabinet pull, and the Emtek Bar cabinet pull. The Schaub 478 is the Haniburton collection, a transitional cabinet pull. For a designer or distributor working a Schaub-specified job, those Emtek Schaub Collection numbers are the same design house under a different label, but they are different collections from Haniburton, so the profile and the drilling are not automatically the same.

The Deltana SBP35 is a modern square bar pull in heavy-duty solid brass, and the Omnia 1969, 1970, and 1971 are modern forged solid brass pulls. The Schaub 478 Haniburton is transitional in style with a 1-1/2 inch projection and a 3/4 inch base. A remodeler matching a flat-panel slab door usually reaches for the square modern profiles; the Haniburton reads transitional and sits comfortably with shaker fronts.

The Haniburton is one collection within Schaub's transitional line, and Schaub cabinet hardware is also carried under the Emtek Schaub Collection, which includes the Emtek 8405 Select cabinet knobs and pulls plus the Alexander, Art Deco, and Bar cabinet pulls. If you want knobs on upper doors and the 478 on the drawer bank, that is where to look for a coordinated finish family rather than mixing brands.

No. The SDC SP50 is a 50MM spindle used for door controls, a component that drives a door lever or latch mechanism. The Schaub 478 Haniburton is a cabinet pull that mounts through the drawer or door front with 8/32 x 1 inch screws and has no spindle interface at all. The two serve unrelated openings and never pair.