Schaub 682 4" Center to Center Stradella Cabinet Pull

Yes. The Schaub 682 Stradella pull is drilled on 4 inch centers, so it drops onto an existing pair of holes bored 4 inches apart with no new drilling. Overall length is 5 inches, which means it covers about half an inch of face on each side of the holes, useful if the old pull left marks or finish shadow.

The 682 takes #8-32 machine screws and ships in the standard 1 inch length. That covers a typical 3/4 inch drawer front or door with room for the threads to seat. If you are mounting to a thicker slab, a 5-piece drawer front with an applied panel, or adding a backplate, you need longer #8-32 screws. The thread size is the standard cabinet hardware thread, so replacements are easy to source.

No. The Schaub 682 Stradella is built on 4 inch center-to-center spacing, so it will not land on 3 inch bores without redrilling the drawer front. For an existing 3 inch pattern, the Trimco 553 series drawer pull is made at 3 inch center-to-center. The Trimco 562 series also lists a 3-1/2 inch option if you are re-boring anyway and want something between the two.

Projection is 1-1/4 inches. That is a deep grip, enough to get a full hand behind on a heavy drawer or a pantry door, but worth checking where doors sit close to a wall return, an adjacent appliance panel, or inside a narrow galley run where a hip catches a protruding pull.

Three finishes: Antique Bronze (AZ), Natural Bronze (NB), and Polished White Bronze (PWB). All three are on the same cast bronze body, so the casting texture and Stradella profile read identically from one finish to the next. If you are standardizing a whole kitchen or a run of units, order the full quantity in one go so the finish lot stays consistent, since living bronze finishes vary between batches.

The Omnia 1970 is listed at the same 1-1/4 inch projection in forged solid brass, so it gives a comparable grip depth if clearance behind the pull is what you sized around. The Omnia 1969 and 1971 sit slightly shallower at 1-3/16 inches. Bear in mind projection matching does not mean hole matching, so confirm the center spacing on whichever you pick.

Not on the same bores. The Schaub 682 Stradella mounts on two #8-32 x 1 inch screws at 4 inch centers. Knob products such as the Orca Hardware CK-15030 and CK-16030 Bachelor Collection round knobs at 1-1/4 inch diameter, and the CK-17025 Blackcomb square knob at 25mm, are single-screw items and would leave one of the existing holes exposed. Use a knob only where the drawer front is new or where you intend to fill and redrill.

The Omnia 1970 is a modern cabinet pull in forged solid brass with a 1-1/4 inch projection, the same standoff from the face as the Schaub 682 Stradella. If you want the handle to sit slightly tighter to the door, the Omnia 1969 and 1971 are both forged solid brass at a 1-3/16 inch projection. Projection matters where drawers sit close to an adjacent appliance or wall return, so confirm your clearance before choosing among them.

Plan on keeping a visible run within one brand. The Schaub 682 Stradella is cast bronze offered in Antique Bronze (AZ), Natural Bronze (NB), and Polished White Bronze (PWB). Peer pulls such as the Omnia 1968/102, 1969, 1970, and 1971 are forged solid brass, and the Orca CK-12001 T-pull is steel in satin nickel, so the base metal and plating differ and living-finish bronzes will not weather the same way as brass. If you need additional profiles on the same job, staying within the Stradella collection or the Emtek Schaub Collection keeps the finish family consistent.

The 682 is cast bronze, not plated zinc or stamped steel, so the color goes through the material rather than sitting on the surface. Chips and wear on a cast bronze pull expose more bronze instead of a bright substrate, which is why bronze holds up in high-turnover multi-family and hospitality millwork. Natural Bronze in particular will darken with handling over time, so expect the look to change rather than fail.

Schaub designs are also carried under the Emtek Schaub Collection, which includes the Emtek 8405 SELECT cabinet pulls and knobs plus the Alexander, Art Deco, and Bar series. If you need a knob or a different length to run alongside the 682 on upper doors and lower drawers, that collection is where to look for a family match.

Yes, Schaub publishes a Proposition 65 warning for the 682, referenced through their product stewardship page. If you are specifying into California residential or commercial work where Prop 65 disclosure is part of your submittal package, flag it at the point of order.