Schaub 691 8" Overall and 3-1/2" Center to Center Stradella Cabinet Pull

The Stradella 691 uses #8-32 x 1 inch machine screws, which is the standard cabinet pull thread. A 1 inch screw covers typical 3/4 inch drawer fronts with room for the pull boss. If you are mounting through a thicker applied front or a slab door over 3/4 inch, you will need longer #8-32 screws.

The Schaub 691 Stradella projects 1-1/2 inch off the face. Where clearance is tight, the Omnia 1970 forged solid brass pull sits at 1-1/4 inch projection, and the Omnia 1969 and Omnia 1971 both sit at 1-3/16 inch, so all three keep the grip closer to the door. Those are modern forged brass profiles rather than the rustic cast bronze look of the Stradella.

The Deltana SBP35 Modern Square Bar Pull is a 3-1/2 inch square bar pull in solid brass, so it drops onto the same two-hole drilling as the Schaub 691, which is also 3-1/2 inch center to center. The difference is styling and material: the Schaub 691 is a rustic cast bronze pull with a 1-1/2 inch projection, while the SBP35 is a squared modern bar in brass. Trimco's 562 Series drawer pull is another option at 3-1/2 inch center to center, with 4 inch and 96mm spacings offered in the same series if you need to match other drawer banks.

The Schaub 691 Stradella is fixed at 3-1/2 inch center to center, so it will not land on a 3 inch drilling without new holes. The Trimco 553 Series drawer pull is built at 3 inch center to center and mounts on the existing holes. If the cabinetry is being re-drilled anyway, the Trimco 562 Series covers 3-1/2 inch, 4 inch, and 96mm spacings in one family.

Three: Antique Bronze (AZ), Natural Bronze (NB), and Polished White Bronze (PWB). All three are living finishes over a cast bronze body, so Natural Bronze in particular will darken with handling. If you are matching a run of existing cabinets, order from the same finish code across the whole job.

Cast bronze, not plated pot metal. That matters for a rustic or hand-forged look, because the finish is worked into a solid bronze body rather than sprayed on a casting, and it holds up to heavy residential and hospitality use.

The Schaub 691 Stradella is 8 inch overall on 3-1/2 inch centers, which suits smaller drawer fronts and doors. For a wider drawer bank, the Omnia 1968/102 forged solid brass pull is built on 4 inch center-to-center spacing, and the Trimco 562 Series is offered in 4 inch as well as 3-1/2 inch and 96mm.

Single-hole knobs are the common mix-up. The Orca Hardware CK-15030 and CK-16030 Bachelor Collection knobs are 1-1/4 inch round knobs and the CK-17025 Blackcomb is a 25mm square knob, all single-fastener cabinet knobs that will not cover the two-hole drilling the Schaub 691 uses at 3-1/2 inch centers. The Orca CK-12001 is a 2 inch wide steel T-pull bar in satin nickel, a different profile and material from the cast bronze Stradella.

The Schaub 691 Stradella is cast bronze and is finished as Antique Bronze, Natural Bronze, or Polished White Bronze. If the job calls for solid brass, the Omnia 1969, 1970, and 1971 pulls are forged solid brass, and the Deltana SBP35 is a solid brass bar pull at 3-1/2 inch center to center, which matches the Stradella's hole spacing.

If 8 inches overall is too long for the front, look at the Emtek Schaub Collection pulls, including the Emtek Alexander, Art Deco, and Bar cabinet pulls, which carry Schaub design in other sizes. For a knob instead of a pull on narrow drawers, the Orca Hardware Bachelor Collection round knob is 1-1/4 inch diameter and needs only a single hole.

Yes. Schaub publishes a Proposition 65 warning for California residents on this cast bronze pull, linked through their product stewardship page.