Schaub 721 3" Center to Center Traditional Cabinet Pull

Yes. The Schaub 721 is a 3 inch center-to-center pull, so it lands on the standard 3 inch drilling most kitchen and vanity doors and drawers already have. Overall length is 3-3/8 inches, so it barely overhangs the existing holes and won't leave old bore marks exposed.

The 721 uses 8/32 thread screws, 1 inch long, which is the standard cabinet pull thread. A 1 inch screw covers typical 3/4 inch fronts with room for the pull's post. If you're mounting through a thicker slab or a front with an applied panel, you'll need longer 8/32 machine screws, sourced separately.

No. The 721 is fixed at 3 inch center-to-center and its 3-3/8 inch overall length won't cover holes drilled wider than that. For 3-1/2 inch or 4 inch drilling, look at the Trimco 562 Series, offered in 3-1/2 inch, 4 inch and 96mm centers, or the Omnia 1968/102 at 4 inch centers.

The Schaub 721 is a traditional-style solid brass pull with 3 inch center-to-center spacing and a 3-3/8 inch overall length. The Trimco 553 Series drawer pull is also offered at 3 inch center-to-center, so it drops onto the same existing two-hole bore pattern without redrilling. The difference is styling and line: the 721 belongs to Schaub's Traditional Designs collection in solid brass, while the 553 is a Trimco drawer pull series.

The Schaub 721 is fixed at 3 inch center-to-center, so a wider bore needs a different pull. The Trimco 562 Series drawer pulls are offered in 3-1/2 inch, 4 inch, and 96mm center-to-center, and the Omnia 1968/102 is a forged solid brass cabinet pull with 4 inch center-to-center spacing. Either covers an opening the 721 cannot reach without new holes.

Projection is 7/8 inch, measured from the door face to the back of the grip. That is enough finger clearance for a gloved hand and keeps the pull clear of an adjacent door in an inside corner run. The mounting posts sit on a 3/8 inch base.

Solid brass. That matters for multi-family and hospitality work where zinc pulls tend to pit and snap at the post; a brass body threads cleanly to the 8/32 screw and holds a plated or living finish better over heavy use.

Twelve finishes: Polished Brass, Antique Brass, Antique Light Brass, Polished Chrome, Satin Nickel, Polished Nickel, Antique Nickel, Distressed Nickel, Oil Rubbed Bronze, Distressed Bronze, Michelangelo Bronze, and Flat Black. If you're matching across a building, order all openings from the same finish code in one go, since living and distressed finishes vary batch to batch by nature.

The Schaub 721 is a traditional-style solid brass pull with a 7/8 inch projection. For a contemporary kitchen, the Deltana SBP35 is a modern square bar pull in solid brass, and Omnia's 1969, 1970 and 1971 are modern forged solid brass cabinet pulls, with the 1969 and 1971 at 1-3/16 inch projection and the 1970 at 1-1/4 inch projection - all standing off the door face farther than the 721.

Not on the same holes. The Schaub 721 mounts on two screws spaced 3 inches apart. Single-hole knobs such as the Orca Hardware Bachelor Collection round knob at 1-1/4 inch diameter, the Bachelor round ring knob at 1-1/4 inch diameter, or the Blackcomb square knob at 25mm use one central screw, so swapping to a knob leaves the second 721 hole exposed unless you fill and redrill.

Yes, and it's a common split: pulls on drawers, knobs on doors. Because the 721 is a two-post pull at 3 inch centers, the knobs only need a single bore, so the two preps are independent. Round knob options include the Orca Hardware Bachelor Collection round knob at 1-1/4 inch diameter and the ring version in the same size. Match the finish name carefully across brands, since finish naming is not standardized.

Yes, Schaub publishes a Proposition 65 warning for this pull through its product stewardship page. Procurement teams buying into California facilities should capture that in their submittal package.