Schaub 732 4" Center to Center Traditional Cabinet Pull

The 732 uses 8/32 thread screws, 1 inch long. That is the standard cabinet pull thread, and 1 inch handles a typical 3/4 inch drawer front with thread to spare. If you are mounting through a thicker applied front, a false front with a subfront, or a drawer box wall behind the face, the 1 inch screw runs short and you need longer 8/32 machine screws.

The Omnia 1968/102 is the closest swap: forged solid brass, 4 inch center-to-center, in a modern profile rather than the 732's traditional styling. Same holes, different design language. Deltana's SBP35 square bar pull is another solid brass modern option, though at 3-1/2 inches it will not reuse a 4 inch prep.

The Schaub 732 is a traditional style solid brass cabinet pull with 4 inch center to center spacing and a 4-3/8 inch overall length. Two peers land on the same 4 inch hole spacing so existing drilling carries over: the Omnia 1968/102 is a forged solid brass cabinet pull with 4 inch center to center spacing, and the Trimco 562 series drawer pull is offered in 3-1/2 inch, 4 inch, and 96mm center to center options. The Omnia and Trimco are modern and drawer-pull profiles rather than the traditional shape of the 732, so the mounting matches while the look changes.

The Schaub 732 is fixed at 4 inch center to center, so it will not land on 3 inch drilling. The Trimco 553 series drawer pull is a 3 inch center to center pull, and the Deltana SBP35 is a 3-1/2 inch heavy-duty solid brass square bar pull if the holes are at 3-1/2 inch. For a 3 inch opening the 553 is the direct answer.

No. The Schaub 732 is a two-hole pull at 4 inch center to center, using 8/32 thread by 1 inch long screws. A single-hole opening needs a knob: the Orca Hardware CK-15030 Bachelor Collection round cabinet knob is 1-1/4 inch diameter, the CK-16030 is a 1-1/4 inch round ring knob in the same collection, and the CK-17025 Blackcomb Collection knob is a 25mm square. All three are catalogued as cabinet knobs rather than pulls.

Projection is 1-1/8 inches, so the grip stands just over an inch off the face. That is enough room for a gloved hand and it clears most inset trim, but check it against anything the pull could strike when the door opens, such as an adjacent perpendicular cabinet run or an appliance panel. The base sits at 3/8 inch.

Solid brass. That matters on a pull that gets grabbed hundreds of times a day in a rental unit or a hospitality property, since zinc-alloy pulls tend to crack at the screw boss where brass does not. It also means the finishes are plated or applied over a brass substrate rather than over die cast.

Twelve finishes: Polished Brass, Antique Brass, Antique Light Brass, Polished Nickel, Satin Nickel, Antique Nickel, Distressed Nickel, Polished Chrome, Oil Rubbed Bronze, Distressed Bronze, Michelangelo Bronze, and Flat Black. For a property manager matching existing hardware, the warm-metal range here is unusually deep, three brass tones and three bronzes, which is what makes matching an older kitchen possible instead of forcing a full changeout.

The Trimco 562 Series drawer pulls are offered in 4 inch center-to-center along with 3-1/2 inch and 96mm, so they cover a mixed-prep job from one series. Trimco's 553 Series is 3 inch only, so it will not land on a 4 inch prep. The Schaub 732 itself is a single-size pull at 4 inch centers in solid brass.

They are not the same part. The Schaub 732 is a cabinet pull in the Traditional Designs collection with 4 inch center to center spacing. The Emtek 8405 belongs to the Emtek SELECT series and is catalogued as a cabinet knob/pull, meaning the 8405 covers knobs as well as pulls. The shared Schaub name on the Emtek side does not make it a drop-in for the 732 drilling.

The Schaub 732 is a traditional style solid brass pull with a 1-1/8 inch projection. Omnia offers several forged solid brass modern pulls: the 1968/102 at 4 inch center to center, the 1969 with a 1-3/16 inch projection, the 1971 also at 1-3/16 inch projection, and the 1970 with a 1-1/4 inch projection. The Deltana SBP35 is a modern square bar pull in solid brass at 3-1/2 inch. Projection differs across these, which matters where the pull sits next to an adjacent door or an appliance panel.

The Schaub 732 is solid brass with a 3/8 inch base dimension. Where a heavier grip is wanted, the Deltana SBP35 is described as a heavy-duty solid brass square bar pull at 3-1/2 inch, and the Orca Hardware CK-12001 is a steel T-pull bar with a 2 inch bar width in satin nickel. The Orca is steel rather than brass and the Deltana sits on 3-1/2 inch spacing, so neither reuses the 732 drilling.

The 732 belongs to Schaub's Traditional Designs collection, in the traditional style. When you are standardizing a whole kitchen or a floor of units, staying inside that collection is how you keep the profile and finish tone consistent across pulls of different lengths and the matching knobs.

No handing. It is a symmetrical two-screw pull on 4 inch centers, so the same part goes on left-hand and right-hand doors and it mounts horizontally or vertically. The only orientation decision is your own: vertical on doors, horizontal on drawers is the usual convention.

The Schaub 732 is a traditional style pull from the Traditional Designs collection. The Emtek Alexander and Emtek Art Deco cabinet pulls are separate series carried under the Schaub Collection name, and both are catalogued as cabinet knob/pull items covering knobs as well as pulls. To keep one series across a kitchen or a unit turnover, stay within the Alexander or Art Deco line rather than mixing the 732 into the run.