Schaub 777 4" Center to Center Mountain Cabinet Pull

The 777 uses 8/32 thread screws, 1 inch long. That length suits a standard 3/4 inch drawer front or door with a little thread to spare. On a thicker slab front, a five-piece front with an applied panel, or anywhere you are going through more than about 3/4 inch of material, you will need longer 8/32 machine screws, which is a common stock item.

The Schaub 777 Mountain is a rustic style cabinet pull in cast bronze at 4 inch center to center. If the door or drawer front calls for a modern profile at that same hole spacing, the Omnia 1968/102 is a forged solid brass cabinet pull with 4 inch center-to-center spacing, so it drops onto the same drilled holes with a different visual language. The Trimco 562 series drawer pull also lists a 4 inch center to center option among its 3-1/2 inch, 4 inch and 96mm choices.

The Schaub 777 Mountain pull is fixed at 4 inch center to center, so it will not land on 3 inch holes without redrilling. For an existing 3 inch spacing, the Trimco 553 series drawer pull is built at 3 inch center to center. If the spacing is 3-1/2 inch, the Deltana SBP35 modern square bar pull is a 3-1/2 inch solid brass pull, and the Trimco 562 series lists a 3-1/2 inch option as well.

Projection is 1-1/4 inches from the face of the door. That is enough clearance to get a gloved hand behind it, which matters in a kitchen or a utility room, but it is also enough to catch a hip or a pocket in a tight galley or a narrow butler's pantry. Measure your walkway before you commit to a run of them.

Cast bronze, solid through the part rather than plated pot metal over a core. That is why the finishes on it are living finishes that change with handling rather than a coating that wears through to a different color underneath. For a high-traffic rental kitchen or a hospitality install, cast bronze holds up better to being grabbed thousands of times than a die-cast pull.

Seven finishes: Antique Silver (AS), Antique Bronze (AZ), Dark Pewter (DP), Italian Nickel (IN), Natural (N), Natural Bronze (NB), and Verde Imperiale (VI). If you are matching an existing run, the finish code is what you order by, so pull the code off the back of one of the pulls already installed rather than matching by eye. Natural and Natural Bronze are the two that read closest to raw metal.

A pull like the Schaub 777 spans two screws on 4 inch centers and gives you a full hand grip, which is what you want on drawers, on anything heavy, and where a lot of people with wet or gloved hands are opening the door. A knob is a single center bore and is faster to install and cheaper per opening. If you go the knob route, the Orca Hardware Bachelor Collection round knob is 1-1/4 inch diameter, and the Blackcomb square knob is 25mm. Knobs will not reuse the 777's two-hole 4 inch bore pattern.

The Schaub 777 Mountain pull projects 1-1/4 inch off the face. The Omnia 1970 modern cabinet pull is forged solid brass with the same 1-1/4 inch projection, so hand clearance off the drawer front is unchanged. If a slightly tighter projection is acceptable, the Omnia 1969 and the Omnia 1971 are both forged solid brass at 1-3/16 inch projection.

Yes. The 777 Mountain pull carries a Proposition 65 warning, which is standard for cast bronze hardware sold into California. Schaub publishes the details on its product stewardship page. If you are buying for a California jobsite or a spec that requires disclosure, this is the one to flag.

The Schaub 777 is a cast bronze rustic pull offered in seven finishes including Antique Silver, Dark Pewter and Verde Imperiale, which is more finish range than a service area usually needs. For a plainer run, the Orca Hardware CK-12001 is a steel T-pull bar with a 2 inch bar width in satin nickel. Where a knob rather than a pull suits the door, the Orca Hardware CK-15030 Bachelor Collection round cabinet knob and the CK-16030 round ring knob are both 1-1/4 inch diameter, and the CK-17025 Blackcomb Collection square knob is 25mm.