Schaub 742 4" Center to Center Country Cabinet Pull

Overall length is 5-1/8 inches, so allow a bit more than that across the drawer front or stile. Projection off the face is 1-1/8 inches, which is the knuckle clearance you get behind the grip. The base measures 1 inch. On inset doors or in tight galley runs, that 1-1/8 inch projection is the number to check against a facing wall or an adjacent appliance handle.

The Omnia 1968/102 is a modern cabinet pull in forged solid brass with the same 4 inch center-to-center spacing, so it drops into the same two drilled holes. The Schaub 742 is a traditional-style pull from the Country collection in solid brass with a 1-1/8 inch projection and a 5-1/8 inch overall length. Same hole spacing, different look: the 742 reads traditional, the Omnia 1968/102 reads modern.

The Schaub 742 is fixed at 4 inch center-to-center and will not land on a 3 inch bore without redrilling. For 3 inch centers, the Trimco 553 series drawer pulls are built at 3 inch center-to-center. The Deltana SBP35 is another option at 3-1/2 inch in heavy-duty solid brass if you are redrilling anyway and want a square bar profile.

No. The Orca Hardware CK-15030 and CK-16030 Bachelor Collection items are 1-1/4 inch diameter cabinet knobs, and the CK-17025 Blackcomb is a 25mm square knob. Knobs mount on a single screw hole. The Schaub 742 is a two-hole pull at 4 inch center-to-center with 8/32 thread x 1 inch screws, so swapping to a knob leaves one of the existing bores exposed unless the doors are redrilled or refaced.

Eight: Oil Rubbed Bronze, Satin Nickel, Polished Chrome, Antique Nickel, Aurora Bronze, Flat Black, Polished Nickel, and Satin Brass. If you're matching existing hardware across a kitchen or a unit turnover, the living finishes (Oil Rubbed Bronze, Aurora Bronze, Antique Nickel) will shift over time with handling, while Polished Chrome and Satin Nickel hold their look.

Solid brass is the base material, not zinc die cast. That matters on high-cycle openings like a trash pull-out or a primary bath vanity, where plated zinc chips at the screw bosses. Note the California Proposition 65 warning that Schaub publishes for this product.

The pull is tapped 8/32, so any 8-32 machine screw threads into it. The supplied screws are 1 inch, which suits a standard 3/4 inch front. For thicker slab fronts, applied moldings, or a back panel on a false front, buy 8-32 screws in the length you need rather than trying to make the stock ones reach.

4 inch centers with a 5-1/8 inch overall length suits full-width drawer banks and standard base cabinet doors. For narrow drawers, spice pull-outs, or small vanity doors, that length can crowd the front and a shorter pull reads better. The Trimco 553 Series drawer pull is a 3 inch ctc option, and the Trimco 562 Series covers 3-1/2 inch, 4 inch, and 96mm centers if you want one series spanning several drawer widths in the same room.

The Trimco 562 series drawer pulls are offered in 3-1/2 inch, 4 inch, and 96mm center-to-center, so you can order the 4 inch to match existing bores and step to the other spacings elsewhere in the same series. The Schaub 742 is built at a single 4 inch center-to-center with a 5-1/8 inch overall length. If every bore in the job is 4 inch, the 742 covers it; if the boring varies, the Trimco 562 series gives you the spacing options within one family.

The Schaub 742 sits 1-1/8 inch off the face. The Omnia 1969 and Omnia 1971 are forged solid brass cabinet pulls at 1-3/16 inch projection, and the Omnia 1970 is forged solid brass at 1-1/4 inch projection, which gives the most hand room of the group. All three are modern-styled, where the 742 is traditional Country.

Yes. The 742 belongs to Schaub's Country collection, and Emtek carries Schaub collection cabinet hardware under its SELECT program (Emtek 8405), which is where to look for matching knobs and companion pieces. A common layout is pulls on the drawers and knobs on the doors, all in one finish from the eight the 742 offers.

Cabinet pull. It's a two-screw, 4 inch center-to-center pull for cabinet doors and drawer fronts, mounted with 8/32 screws. It is not an entry or passage door pull and has no latching function.

The Orca Hardware CK-12001 T-pull bar is steel with a 2 inch bar width in satin nickel. The Schaub 742 is solid brass and is available in satin nickel among its finishes, along with oil rubbed bronze, polished chrome, antique nickel, aurora bronze, flat black, polished nickel, and satin brass. Brass takes the decorative finish range; the steel Orca bar is the plainer utility profile.