Schaub 944 6" Center to Center Grape Wine Bottle Dark Bronze Hi-Lited Cabinet Pull

Mounting is 8/32 thread with 1 inch long screws. That length covers standard 3/4 inch cabinet fronts with thread left to engage the pull. If you are going through a thicker slab front, a face frame, or an applied panel, you will need longer 8/32 machine screws, which are not included beyond the 1 inch size.

The Schaub 944 is a solid brass cabinet pull drilled at 3 inch center-to-center. If the grape and wine bottle motif is too decorative for the room, the Trimco 553 series drawer pull is also offered at 3 inch center-to-center, so it drops into the same two holes without redrilling the door or drawer front.

The Schaub 944 is fixed at 3 inch center-to-center. For wider drawer fronts, the Trimco 562 series drawer pull is offered in 3-1/2 inch, 4 inch, and 96mm center-to-center, and the Omnia 1968/102 cabinet pull is a forged solid brass pull with 4 inch center-to-center spacing. All three share solid brass construction, so finishes can be coordinated across a run of cabinets.

The Schaub 944 has a 1-3/4 inch projection off the face of the door, which is a deliberate part of the sculpted wine bottle form. Where knuckle clearance is tight, the Omnia 1969 and Omnia 1971 cabinet pulls both carry a 1-3/16 inch projection and the Omnia 1970 carries 1-1/4 inch, all in forged solid brass.

Projection is 1-3/4 inches, which is a deep stand-off for a decorative pull. Check the swing clearance where a door sits next to a wall return, an appliance panel, or an inside corner, since a pull at that projection can contact adjacent surfaces before the door is fully open.

Two finish combinations: Antique Brass with Dark Bronze Hi-Lited (AB) and Satin Nickel with Dark Bronze Hi-Lited (SN). Both carry the same dark bronze hi-lited detailing, so you can mix them across a room and keep the accent consistent while matching either warm brass or nickel-toned hardware elsewhere.

Solid brass base material. For a wine cellar, bar, or butler's pantry, that matters: solid brass holds up better to handling and humidity than plated pot metal, and the hi-lited finish wears into the relief rather than flaking off a thin shell.

The Schaub 944 is a figural piece from the Wine Themes collection in the Symphony Inlays style, meant as an accent for a bar or cellar. If you want a plain bar profile instead, the Deltana SBP35 Modern Square Bar Pull is solid brass at 3-1/2 inch, and the Omnia 1968/102 modern pull is forged solid brass on 4 inch centers. For a lower profile modern look, the Omnia 1970 runs a 1-1/4 inch projection against this one's 1-3/4 inches.

For openings already drilled at 3 inch centers, the Trimco 553 Series drawer pull is offered at 3 inch center-to-center and gives you a plain utility profile alongside the decorative Schaub. Trimco's 562 Series covers 3-1/2 inch, 4 inch, and 96mm spacing if other runs in the job use different hole patterns.

They are related but not interchangeable. The Schaub 944 is from the Wine Themes collection in the Symphony Inlays style, with the grape and wine bottle figure. The Emtek Schaub Collection pulls are separate series - Emtek 8405 Select, Alexander, Art Deco, and Bar - each with its own form. If you are matching an existing wine-themed kitchen, the 944 is the one with that motif.

The Schaub 944 is a decorative Wine Themes pull in the Symphony Inlays style, so it reads traditional. For a contemporary look, the Deltana SBP35 is a modern square bar pull at 3-1/2 inch in solid brass, the Emtek Bar cabinet pull is a straight bar form, and the Orca Hardware CK-12001 is a steel T-pull bar with a 2 inch bar width in satin nickel.

No, not without new boring. The Schaub 944 is a two-hole pull on 3 inch center-to-center spacing with 8/32 thread by 1 inch screws. Single-hole knobs such as the Orca Hardware Bachelor Collection round knob at 1-1/4 inch diameter, the Bachelor round ring knob at 1-1/4 inch, or the Blackcomb square knob at 25mm mount on one hole, so swapping to a knob leaves the second hole exposed.

The pull's overall size is given as 7/8 inch with a base dimension of 3/8 inch, on 3 inch centers. That keeps it compact enough for narrow drawer fronts and cabinet stiles, though the 1-3/4 inch projection means it reads as a sculptural piece rather than a flat bar.

Yes. Schaub publishes a Proposition 65 warning for this pull under its product stewardship information, which is the standard notice on solid brass hardware sold into California.

No. The Schaub 944 is a cabinet pull for cabinet doors and drawer fronts. The SDC SP50 is a 50mm spindle in the door controls family, a lock trim component rather than cabinet hardware. If you need a pull for cabinetry, stay with the 944 or another cabinet pull such as the Trimco 553 at 3 inch center-to-center.