Schaub 778 6" Center to Center Mountain Cabinet Pull

The 778 uses 8/32 thread screws at 1 inch long. That covers a standard 3/4 inch cabinet door or drawer front with thread left to seat. If you are mounting through a thicker applied front, a doubled front, or a drawer box plus false front, you will need longer 8/32 machine screws, which is a stock hardware size.

Only where the old pull sat on the same 6 inch centers. The 778 mounts on two posts with a 1-1/8 inch base at each end, so the footprint touching the door face is small. It will not hide a wider backplate or an old three-hole pattern. If you are replacing something with a different bore spacing, you are into plugging and refinishing the fronts, which is the point where most property managers switch to matching the existing spacing instead.

The Schaub 778 is a rustic-style cabinet pull from the Mountain collection in cast bronze. For a modern profile on the same cabinet fronts, the Omnia 1970 is a modern cabinet pull in forged solid brass with a 1-1/4 inch projection, which matches the 1-1/4 inch projection of the 778, so the reach off the door face and the knuckle clearance behave the same way. The Deltana SBP35 is another route, a modern square bar pull in solid brass at 3-1/2 inch center to center for narrower drawer fronts.

The 778 mounts on 6 inch center to center holes with a 7-1/4 inch overall length, so it needs a wide front. For narrow drawers, the Trimco 553 series drawer pulls are 3 inch center to center, and the Trimco 562 series offers 3-1/2 inch, 4 inch, and 96mm center to center. The Deltana SBP35 square bar pull is 3-1/2 inch center to center. All of those are new hole patterns rather than a retrofit into existing 6 inch bores.

No. The Omnia 1968/102 modern cabinet pull is a forged solid brass pull with 4 inch center to center spacing, while the Schaub 778 mounts on 6 inch center to center. The two do not share a hole pattern, so an Omnia 1968/102 will not land on holes drilled for the 778. It is a substitute only where the fronts are being drilled new.

Projection is 1-1/4 inches from the face of the door to the back of the grip. That is enough clearance for a gloved hand, and it is the number to watch in a galley kitchen or a tight corridor where a cabinet door swings toward a wall or an appliance. The mounting posts sit on a 1-1/8 inch base.

Cast bronze. It is a solid cast part, not a plated zinc casting, which is why the finishes read as patina rather than paint. For a rental turn or a hospitality property where hardware gets pulled on hard, that matters more than the finish name does.

Seven: Antique Silver (AS), Antique Bronze (AZ), Dark Pewter (DP), Italian Nickel (IN), Natural (N), Natural Bronze (NB), and Verde Imperiale (VI). Natural and Natural Bronze are the living finishes that will move over time on cast bronze; Dark Pewter and Antique Bronze are the ones that stay closest to where they started. If you are matching hardware already installed on other runs of cabinetry, order one piece in the finish first and hold it against what is on the door.

The Mountain is a rustic cast bronze pull with a textured, forged look, meant for lodge, timber frame, and hand-hewn cabinetry. If the project is contemporary, the shape is wrong no matter how good the finish is, and a clean bar pull suits it better. The Omnia 1968/102 is a forged solid brass modern pull at 4 inch centers, and the Deltana SBP35 is a modern square bar pull at 3-1/2 inch. Both are shorter, so they will not land on holes bored at 6 inches on center.

It is a decorative cast bronze pull built for residential and hospitality millwork, not for institutional casework that takes constant abuse. For drawer banks in commercial casework, Trimco's 553 Series drawer pulls at 3 inch centers or the 562 Series at 3-1/2 inch, 4 inch, and 96mm centers are the utility route. Note the centers are all shorter than the 778's 6 inches, so the hole pattern is not interchangeable.

The Schaub 778 is a two-hole cabinet pull on 6 inch center to center spacing, so it cannot go where a single-bore knob is drilled. For knob prep, the Orca Hardware Bachelor Collection round cabinet pull knob is 1-1/4 inch diameter, the Bachelor Collection round ring cabinet pull knob is also 1-1/4 inch diameter, and the Blackcomb Collection square cabinet pull knob is 25mm diameter. All three are catalogued with a cabinet knob function rather than a pull.

The Schaub 778 is cast bronze and comes in Antique Silver, Antique Bronze, Dark Pewter, Italian Nickel, Natural, Natural Bronze, and Verde Imperiale. The Omnia 1968/102, 1969, 1970, and 1971 modern cabinet pulls are forged solid brass, and the Deltana SBP35 is solid brass. Bronze and brass take plating and living finishes differently, so a bronze pull and a brass pull ordered to similarly named finishes will not necessarily read identically side by side on the same cabinet run. For a uniform run, keep one base material across all the fronts.

The Schaub 778 projects 1-1/4 inch from the door or drawer face. The Omnia 1970 modern cabinet pull carries the same 1-1/4 inch projection. The Omnia 1969 and Omnia 1971 modern cabinet pulls project 1-3/16 inch, a sixteenth tighter to the face, which matters where a drawer bank sits next to a wall return or an appliance panel swings past.

Emtek carries the Schaub Collection, so you can stay inside the same design family while changing shape. The Emtek 8405 Select cabinet pulls, the Alexander cabinet pull, the Art Deco cabinet pull, and the Bar cabinet pull are all Schaub Collection pieces. That is the usual way to mix a statement pull on the drawer bank with something quieter on the uppers without the hardware looking accidental.

No. The SDC SP50 is a 50mm spindle, a door controls item that drives a latch or lock mechanism through a door. The Schaub 778 is a cabinet pull, a surface-mounted grip that screws to a cabinet door or drawer front on 6 inch center to center with 8/32 thread by 1 inch screws. They serve entirely different functions and share no mounting prep.

The Schaub 778 is a rustic cast bronze pull in seven finishes, which suits a design-led kitchen but gives a fleet more part numbers to hold. For a single repeatable line item, the Trimco 562 series drawer pulls cover 3-1/2 inch, 4 inch, and 96mm center to center, so one series answers both imperial and metric hole patterns already in the units. The Trimco 553 series covers 3 inch center to center. The Orca Hardware CK-12001 T-pull bar in steel, satin nickel, is another single-finish standard.