Schaub 783 4" Center to Center Mountain Twig Cabinet Pull

No. The 783 is a fixed 4 inch center-to-center pull, so it will not reach 3 inch holes without filling and re-drilling the drawer fronts. For a 3 inch spacing, the Trimco 553 Series drawer pull is built at 3 inch ctc, and the Deltana SBP35 square bar pull is a 3-1/2 inch option if you are re-boring anyway and want to move up.

The Schaub 783 Mountain collection pull is a rustic solid bronze twig-form pull on 4 inch centers with a 6 inch overall length. If you want the same 4 inch hole spacing in a modern profile, the Omnia 1968/102 is a forged solid brass cabinet pull with 4 inch center-to-center spacing, and the Trimco 562 series drawer pull is offered in a 4 inch center-to-center option alongside 3-1/2 inch and 96mm. All three drop onto the same pair of existing holes, so the change is cosmetic rather than a re-bore of the drawer front.

The Schaub 783 twig pull is drilled at 4 inch centers, so it will not land on 3 inch holes without redrilling. The Trimco 553 series drawer pull is built on 3 inch center-to-center, and the Deltana SBP35 modern square bar pull is a 3-1/2 inch heavy-duty solid brass pull if the openings can take the slightly wider spread. Both are straight replacements on existing hardware rather than a patch-and-drill job on the drawer face.

Five: Antique Silver (AS), Antique Bronze (AZ), Italian Nickel (IN), Natural Bronze (NB), and Verde Imperiale (VI). Natural Bronze and Antique Bronze are the two that read warm against knotty alder or walnut cabinetry, Verde Imperiale is the green-patina option for a lodge or mountain interior, and Antique Silver and Italian Nickel give you a cooler tone if the rest of the room is nickel. All five are the same 783 casting, so you can mix finishes across a kitchen and an adjoining bath and keep the identical twig profile.

Projection is 1-1/2 inches off the face of the door, which is deep for a cabinet pull and leaves room for a gloved hand or a full grip. On a rustic twig casting that depth is part of the look, but it also means the pull stands proud of the cabinet face in a walkway or a tight galley run, where a flatter bar pull would take fewer knocks. The base sits 3/8 inch.

Solid bronze through the casting, not plated zinc. That matters for two reasons on a specification job: the finish is applied over a solid non-ferrous base so a chip or a scuff shows bronze rather than bright white metal, and the part holds up in kitchens, baths, and coastal or high-humidity installs where cast zinc pulls corrode at the screw bosses. It also gives the twig form enough mass to feel like forged work instead of a stamping.

The 783 is part of Schaub's Mountain collection, so if the existing pulls are Mountain series the profile and the finish names line up and later additions match. Order by the same finish code that is on the originals (AS, AZ, IN, NB, or VI). Bronze finishes with a living patina do shift with handling over time, so a pull added years later starts lighter than one that has been in daily use, then catches up.

It comes down to whether the hardware is meant to be seen. The Schaub 783 is a cast bronze twig in a rustic style with a 1-1/2 inch projection, so it is a decorative statement on a lodge, ranch, or reclaimed-wood kitchen. If you want the hardware to disappear, a straight bar is the other direction: the Deltana SBP35 is a modern square bar pull in solid brass, and the Omnia 1968/102 is a forged solid brass modern pull also on 4 inch centers, so it swaps onto the same hole spacing as the 783.

The 783 ships with 8/32 thread x 1 inch screws, which handle a standard 3/4 inch cabinet front with thread to spare. A five-piece front with an applied moulding, a thicker slab door, or a false front with a backer behind it can eat past that 1 inch, and then you need longer 8/32 machine screws. The thread size stays 8/32 either way, so the replacement is a stock item rather than anything proprietary to the pull.

The Schaub 783 stands 1-1/2 inches off the face, which is generous grip for a gloved hand but also more knuckle clearance than a tight galley or an appliance-adjacent drawer may want. The Omnia 1969 and Omnia 1971 modern pulls are forged solid brass at 1-3/16 inch projection, and the Omnia 1970 is 1-1/4 inch. Each sits closer to the door face while still giving a full four-finger grip.

The Schaub 783 is solid bronze with a sculpted twig form, which reads residential and rustic. Where the spec is about wipe-down and uniformity rather than appearance, the Orca Hardware CK-12001 T-pull bar is steel in a satin nickel finish with a 2 inch bar width. It is a plain bar profile, so it standardizes cleanly across a long run of doors and drawers in break rooms, casework, and multi-family unit turns.

Both. It is a cabinet pull with a two-hole 4 inch center-to-center mount, and that is the same prep whether it goes on a drawer front or on a base or wall cabinet door. On drawers it mounts horizontally on the centerline of the front; on doors it mounts vertically on the stile. A 6 inch overall length keeps it in proportion on a narrow drawer as well as a full-height pantry door.

Yes. Schaub publishes a Proposition 65 warning for this pull on their product stewardship page, which is standard for solid bronze hardware sold into California. Institutional and multi-family buyers specifying into California projects should record it with the submittal; it does not restrict the product's use.

The Schaub 783 twig pull is offered in Italian Nickel (IN) along with Antique Silver (AS), Antique Bronze (AZ), Natural Bronze (NB), and Verde Imperiale (VI), so a nickel-toned run can stay within the same twig form. If the existing hardware is a plain bar rather than a rustic form, the Orca Hardware CK-12001 T-pull is a satin nickel steel bar, and the Deltana SBP35 is a solid brass square bar pull at 3-1/2 inch centers. Confirm the tone against a sample before committing a full house or unit count.