Schaub 785 12" Center to Center Mountain Twig Appliance Pull

Yes. The Schaub 785 Mountain Twig appliance pull is drilled on 12 inch center-to-center, so it drops onto an existing 12 inch hole pattern with no new boring. Overall length is 15-5/8 inches, so allow roughly an inch and three quarters of panel beyond each hole before the pull runs into a door edge or an adjacent appliance.

The 785 Mountain Twig pull takes 8/32 thread screws at 1 inch length. That 1 inch machine screw covers a standard cabinet door or drawer front. Panel-ready refrigerator and freezer fronts are often thicker, and appliance manufacturers usually supply their own longer 8/32 screws through the door skin. Match the 8/32 thread and you can run whatever length your panel needs.

Yes. The 785 is the 12 inch center-to-center appliance size in Schaub's Mountain collection, and the collection runs the same twig casting down through shorter cabinet-pull lengths, so the appliance fronts and the base cabinets carry one design. Order the smaller Mountain pulls in the same finish code (AS, AZ, IN, NB, or VI) so the whole kitchen dyes out together.

The Schaub 785 Mountain Twig is an appliance pull at 12 inch center to center with a 15-5/8 inch overall length, in solid bronze with a rustic styling from the Mountain collection. For the smaller openings in the same kitchen, Emtek builds the Schaub Collection cabinet pulls, which are catalogued as cabinet knob and pull function: the Emtek Bar Cabinet Pull, the Emtek Alexander Cabinet Pull, the Emtek Art Deco Cabinet Pull, and the Emtek 8405 Select Cabinet Pull in the Emtek SELECT series. Those give a designer or remodeler a route to carry a single hardware family from the refrigerator and range panels down to the drawer banks, while the 785 handles the appliance-scale opening that needs the long 12 inch mounting spread.

The Schaub 785 Mountain Twig is drilled at 12 inch center to center and runs 15-5/8 inches overall, so it needs an appliance panel or a wide drawer front to land both screws. For narrow drawer fronts, the Trimco 553 Series drawer pulls are 3 inch center to center, and the Trimco 562 Series is offered in 3-1/2 inch, 4 inch, and 96mm center to center. The Deltana SBP35 square bar pull is 3-1/2 inches in solid brass, and the Omnia 1968/102 forged solid brass cabinet pull is 4 inch center to center. Any of those bore spacings fit a standard drawer box where the 785 does not.

Projection is 2-1/8 inches off the face of the door, with a 5/8 inch base where it lands on the panel. That is a deep grip, which is what you want on a heavy appliance door you pull with a full hand or a gloved one. Check clearance against a return wall or a perpendicular cabinet run before you commit, since 2-1/8 inches plus the door swing is real knuckle space.

Solid bronze, not plated pot metal. That matters on an appliance pull more than anywhere else in a kitchen, because it is the handle that gets grabbed twenty times a day and levered on. Bronze also means the living finishes on it wear into the metal rather than off it.

Five: Antique Silver (AS), Antique Bronze (AZ), Italian Nickel (IN), Natural Bronze (NB), and Verde Imperiale (VI). Natural Bronze and Verde Imperiale are the two that read most rustic against a knotty alder or reclaimed timber kitchen; Italian Nickel is the cooler option if the rest of the room is nickel plumbing.

It can, but they are different design families. Emtek's Schaub Collection covers series like Alexander, Art Deco, Bar, and SELECT, which are formal and geometric. The 785 is the Mountain collection, a cast twig in a rustic vocabulary. If your cabinets carry Alexander or Art Deco pulls, a Mountain twig on the refrigerator will read as a different kitchen. Stay inside Mountain for the appliance fronts if that is the look, or pick the Emtek Schaub series that matches what is already hung.

The Schaub 785 Mountain Twig is a rustic solid bronze pull with a 2-1/8 inch projection, and its twig form is the point of the design. For a modern kitchen, the Omnia 1968/102 is a modern forged solid brass cabinet pull at 4 inch center to center, and the Omnia 1970 is a modern forged solid brass pull with a 1-1/4 inch projection, with the Omnia 1969 and Omnia 1971 both at a 1-3/16 inch projection. The Orca Hardware CK-12001 T-Pull Bar is a steel bar pull with a 2 inch bar width in satin nickel. Those sit closer to the door face than the 2-1/8 inch projection of the 785, which matters in a galley where a deep pull catches a hip or a cart.

No. The Schaub 785 is an appliance pull with two mounting points at 12 inch center to center, using 8/32 thread by 1 inch screws, and a full-height appliance panel is normally bored for that pair of holes. A knob is a single-point mount: the Orca Hardware CK-15030 Bachelor Collection round cabinet pull knob and the CK-16030 round ring knob are both 1-1/4 inch diameter, and the CK-17025 Blackcomb Collection square knob is 25mm diameter. Those are knobs, not pulls, and they will not cover or reuse an existing two-hole appliance bore. Use them on cabinet doors and drawers, and keep a two-point pull on the appliance panel.

The Schaub 785 Mountain Twig is a solid bronze rustic pull, 12 inch center to center and 15-5/8 inches overall, with a 5/8 inch base dimension and a 2-1/8 inch projection. Where the drawing simply calls for a bar to grip and the twig profile is not part of the design intent, the Orca Hardware CK-12001 T-Pull Bar is a steel bar pull with a 2 inch bar width in satin nickel, and the Deltana SBP35 is a heavy-duty solid brass modern square bar pull at 3-1/2 inches. Those are straight bar forms in steel and brass rather than a sculpted bronze casting, so a property manager standardizing across many units gets a plainer profile with fewer contours to clean.

Yes, Schaub publishes a Proposition 65 warning for this hardware, which is standard for solid bronze cabinet hardware sold into California. Schaub's product stewardship page carries the notice. Property managers and GCs specifying into California multi-family should have that on file with the submittal.

No, and the two are not related parts. The Schaub 785 Mountain Twig is a cabinet appliance pull in solid bronze, fastened through the door or panel with 8/32 thread by 1 inch screws. The SDC SP50 is a 50mm spindle in the door controls family, a component for door hardware rather than a cabinet pull or any part that mates with one. Ordering the SP50 alongside the 785 gets you a part that has nothing to fasten to.