Schaub 954P 3-3/4" Center to Center Floral Heirloom Treasures Cabinet Pull

Yes, the 954P is a 3-3/4 inch center-to-center pull, so it drops onto cabinet doors or drawer fronts already bored on 3-3/4 inch centers. That is the common spacing on older kitchen and vanity fronts, so it is a straight swap if the existing pull measures 3-3/4 inches between screw centers. Measure hole center to hole center, not end to end, before you order.

The 954P uses 8/32 thread screws at 1 inch long, which is the standard machine screw for cabinet pulls and suits typical 3/4 inch fronts. If you are mounting through a thicker front, a drawer box face, or a face plus an applied panel, 1 inch will not reach and you will need longer 8/32 screws.

The Schaub 954P is a solid brass cabinet pull with 3-3/4 inch center to center spacing. If the existing drill holes are 4 inches apart, the Omnia 1968/102 is a forged solid brass cabinet pull with 4 inch center to center spacing. The Trimco 562 series drawer pulls also cover 4 inch center to center, along with 3-1/2 inch and 96mm options, so a single series can serve a run of cabinets drilled to more than one spacing.

The Schaub 954P projects 1 inch off the cabinet face. For a deeper grip, the Omnia 1970 is a forged solid brass cabinet pull with 1-1/4 inch projection, and the Omnia 1969 and Omnia 1971 both carry 1-3/16 inch projection. All three are modern in styling, where the 954P is a Symphony Inlays pull from the Heirloom Treasures collection, so the change in reach comes with a change in appearance.

Solid brass throughout. That matters on high-traffic cabinetry, rental turnovers, and hospitality millwork where zinc pulls crack at the screw boss after a few years. Solid brass also takes the antique brass finish as a real finish rather than a coating over a dissimilar base.

Antique Brass (AB) is the finish offered on the 954P. There is no second finish choice on this model, so if you are matching a run of cabinets in a different tone you are looking at a different Schaub model rather than a finish option here.

The 3-3/4 inch figure is the screw hole spacing and the 1-5/16 inch overall is the pull's other dimension, its height across the body. Use 3-3/4 inches for drilling and 1-5/16 inches when you are checking that the pull fits within a narrow drawer rail or a slim stile without overhanging the edge.

The 954P is a Symphony Inlays pull from the Heirloom Treasures collection, so it reads traditional and decorative. For a plain modern look in the same solid brass, Deltana's SBP35 modern square bar pull at 3-1/2 inches is one option, and Omnia's 1968/102 forged solid brass pull runs 4 inch center to center. Both are different hole spacings than 3-3/4, so on an existing bore you would be re-drilling.

It works if the openings are all bored at 3-3/4 inch centers and antique brass is the tone you want, since that is the single finish and single spacing this model offers. Where a property has mixed hole spacings, a series with multiple center-to-center options is easier to standardize on, such as the Trimco 562 Series drawer pulls, which come in 3-1/2 inch, 4 inch and 96mm center to center.

Not on the same drilling. The Schaub 954P is a two-post pull on 3-3/4 inch center to center spacing with 8/32 thread by 1 inch screws. The Orca Hardware Bachelor Collection CK-15030 round cabinet pull knob and CK-16030 round ring cabinet pull knob are both 1-1/4 inch diameter knobs, and the Blackcomb Collection CK-17025 is a 25mm square cabinet knob. A knob mounts on a single hole, so swapping to one leaves the second hole from the 954P drilling exposed.

Yes. Emtek sells a Schaub Collection within its cabinet hardware line, including the Emtek 8405 Select cabinet pulls in the Emtek SELECT series, the Emtek Alexander cabinet pull, the Emtek Art Deco cabinet pull, and the Emtek Bar cabinet pull. Each is catalogued as a cabinet knob/pull. The Schaub 954P itself is a Heirloom Treasures pull in the Symphony Inlays style, so the Emtek Schaub Collection pulls are a related family rather than a drop-in match for the 954P pattern.

The Schaub 954P is a decorative solid brass pull in the Symphony Inlays style. For a plain contemporary look, the Deltana SBP35 is a heavy-duty solid brass modern square bar pull at 3-1/2 inches in the SBP series, keeping the solid brass base material. If brass is not required at all, the Orca Hardware CK-12001 is a steel T-pull bar in satin nickel with a 2 inch bar width from the 12-Bar Pull series.

No. The Schaub 954P is drilled at 3-3/4 inch center to center, and the Trimco 553 series drawer pulls are 3 inch center to center. The three quarter inch difference means the holes will not line up, so the 553 series suits new drilling or an existing 3 inch pattern rather than a direct swap for the 954P. Trimco's 562 series covers 3-1/2 inch, 4 inch and 96mm center to center, none of which match 3-3/4 inch either.

Yes. It is a pull, not a knob, and at 3-3/4 inch center to center with a 1-5/16 inch overall body it mounts on drawer fronts and door stiles alike. On drawers, check the 1-5/16 inch dimension against the rail height so the pull sits inside the face. If you specifically want a knob rather than a pull for the smaller doors in the same run, Orca Hardware's Bachelor Collection round cabinet knob is a 1-1/4 inch diameter single-screw option.