Schaub 958P 6-1/2" Center to Center Floral Heirloom Treasures Cabinet Pull

Yes. The 958P is a 6-1/2 inch center-to-center pull, so it drops onto doors or drawer fronts already bored at 6-1/2 inch spacing with no new holes. If your existing holes are at any other spacing, you'd need to plug and re-drill or pick a pull in that spacing instead.

It takes 8/32 thread screws at 1 inch long, which is the standard machine screw size for cabinet pulls. One inch clears a typical 3/4 inch drawer front or door. If you're mounting through a thicker front, a drawer box face plus applied panel, or adding a back plate, you'll need longer 8/32 screws.

The Schaub 958P is a solid brass pull in the Heirloom Treasures collection, Symphony Inlays style, at 6-1/2 inch center to center with a 1-1/4 inch projection. For a plain modern look in the same material, the Omnia 1970 is a modern cabinet pull in forged solid brass with the same 1-1/4 inch projection, and the Omnia 1969 and Omnia 1971 are forged solid brass modern pulls at 1-3/16 inch projection. The Deltana SBP35 is a modern square bar pull at 3-1/2 inch center to center in solid brass, a shorter pull for smaller drawer fronts.

Projection is 1-1/4 inches. That's enough grip clearance for a gloved hand or a full-hand grab on a heavy drawer, but check it against anything adjacent, a pull that stands 1-1/4 inches proud can catch on a neighboring appliance panel or a door swinging into it in a tight galley layout.

Antique Brass (AB) is the finish offered on the 958P. It's a single-finish item, so if you're matching a kitchen already running polished nickel or oil-rubbed bronze, this one won't blend, you'd want a different Schaub finish family for that job.

It works as both, but the 6-1/2 inch spacing and 1-1/4 inch projection put it squarely in drawer and larger door territory, wide drawer banks, pantry doors, and appliance-panel fronts. On a narrow 12 inch upper door a 6-1/2 inch pull will look oversized and may not leave enough rail to land both posts.

No. The Schaub 958P is a two-hole cabinet pull spanning 6-1/2 inch center to center with 8/32 thread x 1 inch screws. The Orca Hardware CK-15030 and CK-16030 Bachelor Collection items are single-post cabinet knobs at 1-1/4 inch diameter, and the CK-17025 Blackcomb square knob is 25mm, so they mount on one hole and will leave the existing two-hole boring exposed.

Material and design intent. The Schaub 958P is solid brass in the Heirloom Treasures collection with a decorative Symphony Inlays style and a 1-1/4 inch projection. The Orca Hardware CK-12001 is a T-Pull bar with a 2 inch bar width in steel with a satin nickel finish. The 958P suits traditional millwork in brass; the CK-12001 is a plain steel bar pull.

The 958P belongs to Schaub's Heirloom Treasures collection in the Symphony Inlays style, a decorative floral inlay look rather than a plain bar. To keep a run consistent, stay inside Heirloom Treasures for the knobs and shorter pulls on the same job, a modern bar pull next to it will read as a mismatch.

Solid brass construction and 8/32 machine screws through the front make it a serviceable choice for higher-traffic millwork, screws can be swapped or retightened rather than the whole pull being replaced. For a purely utilitarian spec where the decorative inlay isn't wanted, the Trimco 553 (3 inch ctc) or 562 Series drawer pulls are plainer institutional options.

No. The Schaub 958P is a cabinet pull in solid brass for cabinet and drawer fronts. The SDC SP50 is a 50mm spindle, a door controls part, and has no role in mounting cabinet hardware.