You may also like
Washers 1/2 X 1-1/2 Fender SS (Jar 100)
Special Features
- Features: A Larger Diameter for Greater Bearing Surface
Manufacturer Resources
Product Specs
- Ansi:
- ANSI
- Division:
- Electrical H1
- Field Application:
- Electrical, Plumbing, Heating and Air Conditioning Industries
- Inside Diameter:
- 2-Jan IN
- Outside Diameter:
- 1/1/2002 IN
- Pack Type:
- Jar
- Product Group:
- Fasteners
- Sub Division:
- Electrical-E H2
- Washer Type:
- Fender Washer
- Department:
- Electrical
- Product Subgroup:
- Washers
- Product Length:
- 3 in
- Product Height:
- 3.6 in
- Product Material:
- Stainless Steel
- Product Weight:
- 2.56 lbs
- Product Width:
- 3 in
Metallics JW12011SS – Frequently Asked Questions
1) What bolt size does the Metallics JW12011SS fender washer fit?
It is a 1/2 inch fender washer with a 1-1/2 inch outside diameter, so it goes over 1/2 inch bolts, rod, or lag screws. The large OD relative to the hole is the whole point: it spreads the load across a much wider bearing surface than a standard flat washer of the same bolt size.
2) Are these Metallics fender washers stainless steel or plated?
Stainless steel, not zinc-plated carbon steel. That matters for outdoor strut runs, damp mechanical rooms, rooftop equipment, and anywhere a plated washer would bleed rust onto a finished surface. Pair them with stainless bolts and nuts to avoid mixing metals in the same joint.
3) When should I use a fender washer instead of a standard flat washer?
Use the fender type when the material under the fastener is soft or oversized: sheet metal, drywall or plaster, plywood, fiberglass, or an enlarged or slotted hole the head of a standard washer would pull through. The JW12011SS gives a 1-1/2 inch bearing face on a 1/2 inch fastener. If you are clamping steel to steel through a tight hole, a standard flat washer is the right call.
4) How many washers come in a jar of the Metallics JW12011SS?
100 pieces, packed in a jar rather than a bag or box, which keeps them from spilling in a gang box or on a service truck. The jar weighs 2.56 lbs.
5) Are these fender washers suitable for electrical and HVAC work, or just general construction?
Metallics lists this washer for the electrical, plumbing, heating and air conditioning trades. Typical uses are hanging strut and channel, anchoring conduit straps and junction boxes to soft or oversized substrates, and trapeze or unistrut assemblies on 1/2 inch rod where a wide bearing face is needed.
6) What part number do I order for a 1/2 inch stainless fender washer from Metallics?
JW12011SS is the Metallics part number for the 1/2 x 1-1/2 stainless fender washer in the 100 piece jar. Use that MPN when matching a submittal or reordering to keep the same material and pack size.
How fast can I get the Metallics JW12011SS delivered?
Most orders ship the same day from our distribution partners, with quick delivery throughout the
continental
U.S.
Need it urgently? Contact Us for expedited shipping options.
Can I return it if it doesn’t work for me?
Yes—ZenSupply offers a hassle-free return policy. If the product isn’t the right fit,
reach out to our support team for a return authorization or setup a return by following our return instructions.
Does the Metallics JW12011SS come with a warranty?
Absolutely. The Metallics JW12011SS is backed by a manufacturer’s warranty.
For full warranty terms, check the product documentation or Contact Us.
How do I get technical support or installation help for the Metallics JW12011SS?
You can call, text, or email our expert support team for fast answers. We’re here to help with
product
selection,
installation tips, and troubleshooting. Contact Us
Why buy the Metallics JW12011SS from ZenSupply?
ZenSupply makes it easy to get the commercial door hardware you need—fast shipping, expert support,
and
rewards on
every order.
Our team is always ready to help you choose the right product for your project.