You may also like
Washers 1/2 X 1-1/2 Fender SS (Jar 100)
Special Features
- Features: A Larger Diameter for Greater Bearing Surface
Manufacturer Resources
Product Specs
- Ansi:
- ANSI
- Division:
- Electrical H1
- Field Application:
- Electrical, Plumbing, Heating and Air Conditioning Industries
- Inside Diameter:
- 2-Jan IN
- Outside Diameter:
- 1/1/2002 IN
- Pack Type:
- Jar
- Product Group:
- Fasteners
- Sub Division:
- Electrical-E H2
- Washer Type:
- Fender Washer
- Department:
- Electrical
- Product Subgroup:
- Washers
- Product Length:
- 3 in
- Product Height:
- 3.6 in
- Product Material:
- Stainless Steel
- Product Weight:
- 2.49 lbs
- Product Width:
- 3 in
Metallics JW1201SS – Frequently Asked Questions
1) What bolt size does the Metallics JW1201SS fender washer fit?
The JW1201SS is a 1/2 inch fender washer, so it goes over 1/2 inch bolts, rod, or anchors. The 1-1/2 inch outside diameter gives you three times the bolt diameter in bearing surface, which is the point of a fender washer versus a standard flat washer.
2) Is the Metallics JW1201SS washer stainless steel, and can I use it outdoors?
Stainless steel, so it holds up in damp and exterior locations where a plain or zinc washer would rust and stain the surface under it. That makes it the one to use on rooftop equipment supports, wet locations, and coastal work.
3) Will a 1/2 inch fender washer stop a bolt head from pulling through sheet metal or strut?
That is exactly the job. With a 1-1/2 inch outside diameter on a 1/2 inch bolt, the JW1201SS spreads the load across a much wider footprint than a standard flat washer, which is what keeps fasteners from crushing through thin sheet metal, drywall, soft wood, or oversized holes in strut and channel.
4) How many Metallics JW1201SS fender washers come in a jar?
100 pieces, packed in a jar rather than a bag, so the washers stay contained on the truck and on the cart. One jar covers a full run of hangers or equipment mounts without repacking.
5) Should I use a fender washer or a standard flat washer on 1/2 inch rod?
Pick the fender washer when the hole is oversized or the material is soft or thin, because a standard 1/2 inch flat washer has far less bearing surface and will pull through. Use a standard flat washer when you are clamping steel to steel through a properly sized hole and clearance around the bolt is tight, since the 1-1/2 inch outside diameter of the JW1201SS can foul against adjacent hardware or the leg of a strut.
6) What trades use a 1/2 inch stainless fender washer like this?
Metallics lists the JW1201SS for the electrical, plumbing, heating and air conditioning industries. Typical use is seismic and trapeze hanger assemblies on 1/2 inch rod, equipment and panel mounting, and anywhere an oversized or ragged hole needs to be bridged.
How fast can I get the Metallics JW1201SS delivered?
Most orders ship the same day from our distribution partners, with quick delivery throughout the
continental
U.S.
Need it urgently? Contact Us for expedited shipping options.
Can I return it if it doesn’t work for me?
Yes—ZenSupply offers a hassle-free return policy. If the product isn’t the right fit,
reach out to our support team for a return authorization or setup a return by following our return instructions.
Does the Metallics JW1201SS come with a warranty?
Absolutely. The Metallics JW1201SS is backed by a manufacturer’s warranty.
For full warranty terms, check the product documentation or Contact Us.
How do I get technical support or installation help for the Metallics JW1201SS?
You can call, text, or email our expert support team for fast answers. We’re here to help with
product
selection,
installation tips, and troubleshooting. Contact Us
Why buy the Metallics JW1201SS from ZenSupply?
ZenSupply makes it easy to get the commercial door hardware you need—fast shipping, expert support,
and
rewards on
every order.
Our team is always ready to help you choose the right product for your project.