You may also like
Metallics TEKPK1SS Screws 8--10 Pn Ph D-Pt TS Kit SS (Trey 1)
Model: MET-TEKPK1SS
Screws 8--10 Pn Ph D-Pt TS Kit SS (Trey 1)
Kit Components
(1) #2 x 2 IN Phillips Power Bit
(50) 8 x 1 IN Pan Head Phillips SS Self Drilling Screw, (80) 10 x 1/2 IN Pan Head Phillips SS Self Drilling...
Metallics
$264.40
Metallics TEKPK1 Screws 8--10 Pn Ph D-Pt TS Kit St-zn (Trey 1)
Model: MET-TEKPK1
Screws 8--10 Pn Ph D-Pt TS Kit St-zn (Trey 1)
Additional Notes
other sizes and quantities available by request
Kit Components
(100) 8 x 1/2, 60 - 8 x 3/4, (50) 8 x 1, (80) 10 x 1/2, (50) 10 x...
Metallics
$134.71
$117.20
10-32 x 1-1/4 PN PH TS D-Pt
Manufacturer Resources
Product Specs
- Division:
- Electrical H1
- Product Family:
- Connectivity
- Sub Division:
- Electrical-E H2
- Department:
- Fasteners
- Product Group:
- Screws
- Product Subgroup:
- Tapping Screws
- Product Type:
- Tapping Screw
Metallics JGSTK114 – Frequently Asked Questions
1) Is the JGSTK114 a self-drilling screw or does it need a pilot hole?
The JGSTK114 is specified with a drill point, so the tip does the drilling and tapping in one pass on sheet steel. No separate pilot hole or tapped hole is needed in thin gauge metal, which is why these get used for fastening into sheet steel enclosures, raceway, and framing instead of pre-drilling.
2) Will a 10-32 screw thread into my steel electrical box or device plate?
Yes. 10-32 is the thread the electrical trade standardizes on for device mounting, box ears, cover plates, and ground screw holes, and the JGSTK114 carries that thread. The 1-1/4 inch length gives you reach through a plate and plaster ring or through stacked sheet metal rather than just a surface bite.
3) What part number do I order for the Metallics 10-32 x 1-1/4 pan head drill point screw?
Order Metallics MPN JGSTK114. It is a single configuration, so there is no finish or drive option to specify beyond the part number itself.
4) Why choose a pan head Phillips screw here instead of a hex or flat head?
A pan head sits proud on the surface with a broad bearing face, so it clamps sheet metal and plate stock without needing a countersink. That is the opposite of a flat head, which requires a countersunk hole to seat flush. The Phillips drive on the JGSTK114 means a standard #2 driver bit in a cordless screwgun, which is what most installers already have in hand for sheet metal work.
How fast can I get the Metallics JGSTK114 delivered?
Most orders ship the same day from our distribution partners, with quick delivery throughout the
continental
U.S.
Need it urgently? Contact Us for expedited shipping options.
Can I return it if it doesn’t work for me?
Yes—ZenSupply offers a hassle-free return policy. If the product isn’t the right fit,
reach out to our support team for a return authorization or setup a return by following our return instructions.
Does the Metallics JGSTK114 come with a warranty?
Absolutely. The Metallics JGSTK114 is backed by a manufacturer’s warranty.
For full warranty terms, check the product documentation or Contact Us.
How do I get technical support or installation help for the Metallics JGSTK114?
You can call, text, or email our expert support team for fast answers. We’re here to help with
product
selection,
installation tips, and troubleshooting. Contact Us
Why buy the Metallics JGSTK114 from ZenSupply?
ZenSupply makes it easy to get the commercial door hardware you need—fast shipping, expert support,
and
rewards on
every order.
Our team is always ready to help you choose the right product for your project.