Metallics JPMP23 6-32 x 3/8 in...
IN STOCK (leaves warehouse same day if ordered before 3pm ET)
$50.11
$0.11
Metallics JPMP23 6-32 x 3/8 in. Pan Head Phillips Machine Screws - Steel Zinc - 100qty

Metallics JPMP23 6-32 x 3/8 in. Pan Head Phillips Machine Screws - Steel Zinc - Each

(No reviews yet) Write a Review

Model: JPMP23
Selected Model is

In Stock (leaves warehouse same day if ordered before 3pm ET)

$50.11
$0.11
Adding to cart… The item has been added
Free Shipping on orders over $199
We price match and offer bulk discounts! Click Add to Quote. It's quick and easy.
✨
Earn points with this purchase! You can redeem points for giftcards, iPads, XBox's and more. View Rewards
Free Keying on all locks
You may also like
6-32 x 3/8 in. Pan Head Phillips Machine Screws - Steel Zinc - 100qty

  • Additional Notes

    • Other sizes and quantities available by request | Tensile strength values for stainless screws are offered as approximations only; there is no single standard for the performance requirements of stainless machine screws.

  • Features

    • Steel Zinc Material
    • 6-32 Diameter, 3/8" Length
    • Pan head with Phillips Drive

Manufacturer Resources

Product Specs

Minimum Purchase:
100 units
Arra Compliant:
N
Buy American Compliant:
No
Dimensional Standard:
ASME B18.6.3-2010
Division:
Electrical H1
Drive Type:
Phillips
Driver Size:
#2
Fastener Head Height:
0.087 - 0.097 in.
Fastener Head Type:
Pan
Fastener Head Width:
0.256 - 0.27 in.
Fastener Length:
8-Mar
Hardness:
Rockwell B70-B100
Language Code:
EN
Material Standard:
AISI 1006 - 1022
Order Minimum Imperial:
100
Order Minimum Uom Imperial:
CT
Pack Type:
Jar
Phillips Recess Diameter:
0.159
Product Group:
Fasteners
Recess Penetration Gaging Depth:
0.055 - 0.080
Sub Division:
Electrical-E H2
Tensile Strength:
60000 psi minimum
Thread Per Inch:
32
Department:
Electrical
Product Subgroup:
Screws
Product Type:
Machine Screw
Type2:
Machine Screw
Series:
PMP
Product Finish:
Zinc
Product Details:
Machine Screw
Product Material:
Steel Zinc

Metallics JPMP23 – Frequently Asked Questions

1) Do these screws meet a recognized dimensional standard so they interchange with what is already in my boxes?
Yes. The JPMP23 is made to ASME B18.6.3-2010, the standard for inch-series machine screws, so the thread and head geometry interchange with any other 6-32 pan head built to that spec. That is what lets you mix brands across a facility without sorting.
2) Are these Metallics screws Buy American or ARRA compliant for a government job?
No. The JPMP23 is not Buy American compliant and is not ARRA compliant, with country of origin listed as multiple. If your project carries a domestic-content requirement, these will not satisfy it.
3) What size Phillips driver fits these Metallics machine screws?
A #2 Phillips. The recess on the JPMP23 measures 0.159 inch in diameter with a gaging depth of 0.055 to 0.080 inch, so a #2 bit seats fully. Using a #1 will cam out and chew the recess.
4) How much clearance does the pan head take up, and will it sit flush in a countersunk hole?
No, a pan head sits on top of the surface. The JPMP23 head measures 0.256 to 0.270 inch across and 0.087 to 0.097 inch high, so plan on roughly a tenth of an inch of head standing proud. For a flush finish in a chamfered hole you need a flat head machine screw, not a pan head.
5) Are these zinc plated steel screws OK for outdoor or damp locations?
The JPMP23 is AISI 1006 to 1022 carbon steel with a zinc finish, which is a dry-location plating. It holds up fine inside panels, boxes and interior device work. For wet locations, exterior enclosures or coastal air, go to a stainless 6-32 machine screw instead, since zinc plating on steel will eventually white-rust and then red-rust.
6) How strong is a 6-32 steel zinc machine screw, and can I torque it down hard?
Minimum tensile strength is 60,000 psi, with hardness in the Rockwell B70 to B100 range. That is standard low-carbon machine screw strength, fine for clamping device plates, covers, brackets and panel components. It is not a structural fastener, and at 6-32 the thread is small enough that over-torquing will strip a tapped sheet metal hole before the screw fails.
7) What is the difference between a machine screw like this and a sheet metal or self-tapping screw?
A machine screw such as the JPMP23 has a uniform 32 TPI machine thread and a blunt end, so it needs a pre-tapped hole or a nut. It will not cut its own thread. If you are driving into unthreaded sheet steel, use a self-tapping or sheet metal screw. If the hole is already tapped 6-32, as device boxes, straps and enclosure flanges typically are, this is the correct screw.
8) How do these machine screws ship, and what is the minimum I can buy?
They come in a jar of 100, and 100 count is the order minimum for the JPMP23. Good shelf item for a service van or an MRO crib since the jar keeps them sorted.
How fast can I get the Metallics JPMP23 delivered?
Most orders ship the same day from our distribution partners, with quick delivery throughout the continental U.S. Need it urgently? Contact Us for expedited shipping options.
Can I return it if it doesn’t work for me?
Yes—ZenSupply offers a hassle-free return policy. If the product isn’t the right fit, reach out to our support team for a return authorization or setup a return by following our return instructions.
Does the Metallics JPMP23 come with a warranty?
Absolutely. The Metallics JPMP23 is backed by a manufacturer’s warranty. For full warranty terms, check the product documentation or Contact Us.
How do I get technical support or installation help for the Metallics JPMP23?
You can call, text, or email our expert support team for fast answers. We’re here to help with product selection, installation tips, and troubleshooting. Contact Us
Why buy the Metallics JPMP23 from ZenSupply?
ZenSupply makes it easy to get the commercial door hardware you need—fast shipping, expert support, and rewards on every order. Our team is always ready to help you choose the right product for your project.
!