Deltana SSP3615 36" Extra Large Contemporary Pull, Single Side

The SSP3615 is 37-1/2 inches overall with its mounting centers 36 inches apart, so you need a little over three feet of uninterrupted door face and your two holes drilled 36 inches on center. The bar is 1-1/2 inches wide and stands 3-1/2 inches off the face. On a storefront or a stile-and-rail door, check that nothing else on the face (closer arm, lock trim, kick plate top edge) falls inside that 37-1/2 inch run before you lay it out.

One pull, one face. The SSP3615 ships as a single-side unit with the hardware to mount that one pull. Deltana builds the Contemporary extra large stainless pulls as back-to-back kits as well, so if you want matching 36 inch pulls facing each other on both faces of the door, order the back-to-back version rather than buying two singles.

The Deltana SSP3615 is built to one span: 36 inches center to center, 37-1/2 inches overall, with a 1-1/2 inch width and 3-1/2 inch projection in solid stainless steel. When the opening needs a different span, the ABH AB3330 series is an offset round end pull offered with custom length options, so the pull is cut to the dimension the door or the drawing calls for rather than to a stock size. For fixed lengths in the same heavy duty family, the Ives 8103HD is a straight pull in 1 inch round with through bolt mounting, and the Ives 8102HD is a straight pull on a 3/4 inch round bar with 1-1/2 inch clearance.

Brushed Stainless is the one, listed by Deltana as US32D. The only other choice on the SSP3615 is Paint Black, which is the US19 painted finish. Two finishes total, and the pull is solid stainless steel under either one, so a satin stainless entrance suite matches without hunting for a plated equivalent.

Finish is the only decision: Paint Black or Brushed Stainless. Mounting centers are fixed at 36 inches, overall length at 37-1/2 inches, and there is no handed version to get wrong, so nothing else goes on the PO. That is unlike some decorative pulls, where handing is part of the order, for instance Emtek's Lost Wax Cast Bronze Art Nouveau 8 inch pull is ordered with handing selected.

Fasteners are in the box. Deltana ships the SSP3615 with all the hardware needed to mount the pull, so there is nothing additional to order for the pull side of the door. Plan your own prep though: the holes go 36 inches apart on the door face and you are drilling to suit whatever the door is built from.

It is built for that. Solid stainless steel construction throughout, and Deltana positions the Contemporary extra large pulls as the heavy duty option for larger doors, catalogued for commercial use. The grip gives you 3-1/2 inches of projection off the door face across a 37-1/2 inch run, so a gloved hand, or two hands on a heavy exterior leaf, works anywhere along the bar. For an exterior opening, Brushed Stainless leaves you with bare stainless at the grip rather than a painted surface that takes the wear.

Scale and grip profile. The Deltana is a full-height entrance pull, 37-1/2 inches long on 36 inch centers with a 1-1/2 inch wide grip and 3-1/2 inch projection. The Ives and ABH pulls are round-bar hardware at conventional pull lengths: the Ives 8102HD is a 3/4 inch round bar straight pull with 1-1/2 inch clearance, the 8103HD a 1 inch round bar with through-bolt mounting, the ABH AB3300 a 1 inch diameter straight flat end pull, and the ABH AB7200 a 7/8 inch solid stainless flat end pull with through-bolt mounting. Pick the Deltana when you want one long pull spanning the leaf; pick the round-bar Ives or ABH when you are matching existing round pulls or the spec calls for through-bolt mounting.

The Deltana SSP3615 is fixed at 36 inch centers and 37-1/2 inches overall, so it does not scale down. For a shorter commercial pull, the ABH AB3330 series is offered with custom length options, and the ABH AB3310 offset flat end and Ives 8169 C style offset pull are stock commercial pulls at conventional lengths. If you want something much shorter and decorative, Emtek's 8 inch pulls in the Baden, Brisbane, Arts and Crafts, and Art Nouveau patterns are the short end of the range.

A push plate, ordered separately. Trimco's 1001-1 heavy duty push plate is 3 x 12 inches, the 1041 half-round is 8 x 16 inches, and the 1070 series classic push and pull plates measure 3-1/2 x 15 inches. Trimco also makes the 1035 Ultimate Restroom Pull if the opening is a restroom door. If instead you want the same 36 inch pull on both faces, go to the Deltana back-to-back kit rather than mixing a pull and a plate.

The SSP3615 comes one way only: 36 inch centers, 37-1/2 inches overall, in Paint Black or Brushed Stainless, with no offset variant to order. If the spec is written for a 45 degree offset ADA pull, the Ives 8145EZHD is the part that reads that way, listed as a 45 degree offset pull with heavy duty mounting hardware in the ADA compliant EZ series. The ABH AB3310 and AB3330 are the other offset pulls to look at when the drawing wants an offset grip.

They solve different problems. The Cal-Royal PUL-175 is a night latch cylinder pull, 3-1/2 inches in height, stainless steel construction, sized to sit around a rim cylinder on a night latch installation. The Deltana SSP3615 is a 36 inch center to center stainless pull for the door face with no cylinder function at all. If the door needs a grip around an existing rim cylinder, the PUL-175 is the part; if it needs a full length handle, it is not.

No. The SSP3615 is a pull you grip, a stainless bar standing 3-1/2 inches off the door face. The Trimco 1001-1 is a heavy duty push plate at 3 inches by 12 inches and the Trimco 1041 is a half-round push plate at 8 inches by 16 inches; both are flat plates that protect the push face and give nothing to grab on the pull side. The Trimco 1070 series classic push and pull plates at 3-1/2 inches by 15 inches pair a plate with a pull, which is the closer answer when one door face needs a plate and the other needs a grip.

The SSP3615 runs straight, a 37-1/2 inch stainless bar standing 3-1/2 inches off the face. Offset pulls bend the grip away from the door so the hand clears the frame or a mullion. The Ives 8145EZHD is a 45 degree offset pull in the ADA compliant EZ series with heavy duty mounting hardware, the Ives 8169 is a C style offset solid pull at 1 inch diameter with heavy duty mounting, and the ABH AB3310 is an offset flat end commercial grade surface mount pull. Where an accessibility review is driving the selection, the 8145EZHD is the one in the set carrying the ADA compliant description.

The Deltana SSP3615 is a single side pull and ships with the hardware needed to install it. Where the specification calls out through bolting, the Ives 8103HD is a heavy duty straight pull, 1 inch round, with through bolt mounting, and the ABH AB7200 is a solid stainless steel flat end pull at 7/8 inch diameter with through bolt mounting. Through bolted pulls put fasteners through the full door thickness, so confirm what lands on the opposite face before committing on a door that already carries a plate or a second pull.

Deltana lists it as a 36 inch appliance pull, and the numbers match that use: 36 inch mounting centers, 37-1/2 inches overall, 3-1/2 inch projection, 1-1/2 inch grip width, solid stainless steel with the mounting hardware supplied. Measure the existing hole spacing on the panel first, since the 36 inch centers are fixed and there is no adjustment in the pull.