Deltana SSP1810 18" Contemporary Pull, Single Side

The Contemporary stainless pull kits include the installation hardware required for both glass and wood doors, so a glass front installer doesn't need to source separate glass fittings. Confirm your glass thickness falls in the 1-3/8 to 1-7/8 inch range the pull is set up for.

The SSP1810 is the single side configuration: one 18 inch pull mounted on one face of the door. Use it on a push/pull opening where the other face gets a push plate, or on a door where only the pull side is handled. If you want a matching pull on both faces of the same door, you need the back-to-back option instead, not this one.

No. The SSP1810 is a single side pull, so it gives a grip on the pull face of the door. A push plate is the opposite half of the trim set: the Trimco 1001-1 is a heavy duty push plate at 3 inches by 12 inches, and the Trimco 1041 is a half round push plate at 8 inches by 16 inches. Those go on the push side and offer nothing to grab. If you want both halves in one specification, the Trimco 1070 series classic push/pull plates run 3-1/2 inches by 15 inches.

The SSP1810 is an 18 inch stainless steel single side pull with a 1 inch thickness. The closest peer on diameter is the Ives 8103HD heavy duty straight door pull, which uses a 1 inch round bar with through bolt mounting. Both are straight round bar pulls at the same 1 inch section, so the grip feels the same in the hand. The difference is mounting method and styling: the Deltana ships as a stainless contemporary pull in paint black, polished stainless, or brushed stainless, while the Ives 8103HD is specified around its through bolt mounting.

For an offset rather than a straight bar, the ABH AB3310 is an offset flat end door pull handle in a commercial grade surface mount, and the ABH AB3330 series is an offset round end pull available with custom length options. On the Ives side, the 8169 is a C style offset solid door pull at 1 inch diameter with heavy duty mounting, matching the 1 inch section of the Deltana SSP1810, and the Ives 8145EZHD is a 45 degree offset pull with heavy duty mounting hardware that is ADA compliant.

The Ives 8145EZHD is the peer that carries an ADA compliant callout: it is a 45 degree offset door pull with heavy duty mounting hardware in the EZ series. The Deltana SSP1810 is an 18 inch stainless steel single side contemporary pull with a 1 inch grip section, fitting doors 1-3/8 inch to 1-7/8 inch thick. If the drawing names ADA compliance on the pull itself, specify the 8145EZHD; if the SSP1810 is chosen for the look, confirm mounting height and clearance against the opening.

Three: Paint Black, Polished Stainless, and Brushed Stainless. Brushed stainless is the usual pick for matching existing commercial hardware and hiding fingerprints on a high-traffic entry; polished reads brighter on a storefront; paint black is the one that will show wear at the grip first.

It is classed as commercial and built from solid stainless steel throughout, with a 1 inch grip section. Stainless is the right substrate for an exterior entry or a coastal opening where a plated finish would eventually break down.

For a heavier-duty straight pull in the same 1 inch round profile, the Ives 8103HD is a through-bolt mounted heavy duty straight pull. If you want an offset grip instead of straight, the Ives 8169 is a C style offset solid pull, also 1 inch diameter and heavy duty. The ABH AB7200 is a solid stainless flat end pull at 7/8 inch diameter with through-bolt mounting, so it is a slightly slimmer grip in the same material as the Deltana.

If ADA compliance is called out on your drawing, the Ives 8145EZHD is a 45 degree offset pull listed as ADA compliant with heavy duty mounting hardware. Spec that one where the opening has to meet the requirement, rather than substituting a straight contemporary pull.

The Deltana contemporary stainless steel pulls are made in three lengths, and the SSP1810 is the 18 inch. If you need a length outside what the contemporary series carries, the ABH AB3330 series offset round end pull is offered with custom length options. Keep in mind the AB3330 is an offset profile rather than the straight bar of the SSP1810, so the two will not read the same on a glass front.

The Deltana SSP1810 is a 1 inch thick stainless steel pull. For a lighter looking bar with the same straight flat end profile, the ABH AB7200 is a solid stainless steel flat end pull handle at 7/8 inch diameter with through bolt mounting. The ABH AB3300 straight flat end commercial door pull sits at 1 inch diameter if you want to stay at the same section but in a flat end rather than contemporary styling.

They solve different problems. The SSP1810 is an 18 inch stainless steel single side pull for commercial openings, and it fits doors 1-3/8 inch to 1-7/8 inch thick with installation hardware for glass and wood doors included. The Trimco 1035 Ultimate Restroom Pull is a heavy duty pull built specifically for the restroom exit condition. If the restroom door is a glass or wood door and you want the same contemporary bar you are using elsewhere in the building, the SSP1810 carries the look through; if you want a purpose built restroom pull, the 1035 is the one to specify.

Not as a swap. The Cal-Royal PUL-175 is a night latch cylinder pull, 3-1/2 inches in height, in stainless steel construction. It is a short pull built to sit around a rim cylinder on a night latch application. The Deltana SSP1810 is an 18 inch stainless steel pull with a 1 inch section, mounted through a door 1-3/8 inch to 1-7/8 inch thick, and has no cylinder prep. They share stainless construction and nothing else.

The Ives 8102HD is a heavy duty straight door pull using a 3/4 inch round bar with 1-1/2 inch clearance behind it. The Deltana SSP1810 is a straight stainless pull with a 1 inch thickness, so it is a fuller bar in the hand. Both are straight profiles, so either reads as a plain bar on the door; the 8102HD gives you a published knuckle clearance figure, and the SSP1810 gives you the heavier 1 inch section in stainless with paint black, polished stainless, or brushed stainless finishes.

No handing to specify. It's a symmetrical straight bar pull mounted vertically on one face, so the same part works on a left or right hand door and on either leaf of a pair. Offset and decorative pulls are where handing comes into it, for instance Emtek's Art Nouveau pull is ordered by hand.

Priced and sold each, one pull per unit. On a pair of doors where both leaves get a pull, order two.