Emtek 7107 Sandcast Bronze #5 7-1/4" Non-Keyed Sideplate Tubular Lockset, Passage

Yes. The 7107 uses one standard 2-1/8 inch cross bore, so it drops into a door already prepped for a common bored lockset. Backset is adjustable between 2-3/8 and 2-3/4 inches, and it covers doors from 1-3/8 to 1-3/4 inches thick. The one thing to check is the sideplate itself: it is a 7-1/4 inch plate, so the door stile has to be wide enough and clear of glass or panel edges for that plate to sit flat.

Neither. Passage function only, non-keyed, with no cylinder and no privacy button. The latch retracts from both sides at all times, which makes it right for hallways, closets, pantries and doors between rooms. If you need the door to lock for a bath or bedroom, you need a privacy sideplate set instead, and for an entry you need a keyed one.

Handing is a required choice, right hand or left hand. It matters for levers, which have to point toward the latch side; on a knob the trim is symmetrical but the sideplate order still asks for the hand. Stand outside the door: if the hinges are on your right, it is a right hand door.

Measure from the door edge to the center of the 2-1/8 inch bore. Residential doors are most often 2-3/8 inches; heavier or wider doors frequently run 2-3/4. Backset is a required selection on the 7107 and the latch supplied matches what you pick, so get the measurement before you order rather than after the door is hung.

Not as standard. The 7107 covers 1-3/8 to 1-3/4 inch doors. Thicker doors need a longer spindle and screw package, so enter your actual door thickness in the door thickness field when ordering rather than assuming the standard set will reach. If the door is well over 1-3/4, confirm the thickness first, because the wrong spindle length means the trim will not pull up tight to the door face.

The Emtek 7107 is a non-keyed passage set, so it latches the door but never locks - there is no cylinder in it. For a keyed opening on a sideplate-style lever, the Omnia D12036A is a single cylinder deadbolt lever lockset in solid brass, and the Omnia D12036AC is the double cylinder version of the same lever lockset with a sideplate design. Choose the single cylinder where a thumbturn on the inside is acceptable and the double cylinder where both sides must be keyed, which is typically an exterior door with glass nearby - check local egress code before specifying double cylinder.

No. The Emtek 7107 is a tubular passage lockset and includes a working latch and strike plate, so it needs a 2-1/8 inch cross bore and a 2-3/8 inch or 2-3/4 inch backset latch bore. For a surface-mounted door with no latching - a false pair, a ball-catch closet door, or a fixed panel - the Omnia D12036PD is a double dummy deadbolt lever lockset with plates at 5-1/2 inch center to center, which mounts without any bore for a latch. Use the 7107 where the door must stay closed on a latch and the dummy set where it does not.

It ships as a complete set: the sideplates, your chosen knob or lever trim, the latch and the strike plate. Screws for mounting are part of the set. You are not buying a cylinder (it is non-keyed) and you are not buying a separate rose or latch. If the same door also needs a deadbolt, that is a separate order.

Any Sandcast Bronze knob or lever in the line. Levers: Aurora, Bryce, Cimarron, Cody, Durango, Lariat, Mariposa, Montrose, Teton and Yuma. Knobs: Butte, Egg, Round, Winchester, Bristol, Hampton, Lowell, Windsor, Astoria, Diamond, Georgetown, Modern Disc, Modern Square, Old Town and Providence. That lets you run the same sideplate on every door in the house and vary the trim, or keep one style throughout.

Three: Flat Black Bronze (FB), Medium Bronze (MB) and Tumbled White Bronze (TWB). These are sandcast bronze finishes, so they are living finishes with visible casting texture and slight piece-to-piece variation, which is the point of the look. If you are matching existing Emtek sandcast hardware on other doors in a building, order the same finish code rather than matching by eye.

It is classed as residential hardware. For high-traffic commercial openings, corridors or anything on a fire-rated door, spec a commercial bored or mortise lock instead. Where the 7107 fits well is single-family, custom residential, high-end multi-family unit interiors and hospitality rooms where the rustic sandcast look is part of the design.

No, different function. The 7107 is a passage set, latch only, no locking. The Omnia D12036A is a single cylinder deadbolt lever lockset and the D12036AC is the double cylinder version, both combining lever trim with a keyed deadbolt on one plate. If you want the sideplate look on a door that has to lock, those are the direction. Omnia also offers the D12036PD, a double dummy version with plates, for a door that does not latch at all.

They are different ways of dressing a similar looking plate. The Emtek 7107 is a 7-1/4 inch sideplate set in sandcast bronze, non-keyed passage function, offered in Flat Black Bronze, Medium Bronze and Tumbled White Bronze, and the inside trim is chosen from a long list of sandcast knob and lever designs. The Omnia D12036 group is solid brass lever lockset construction and is built around a deadbolt: D12036A single cylinder, D12036AC double cylinder, D12036PD double dummy. So the choice is between a bronze passage set with a latch only and a brass set that carries a bolt or imitates one.

Treat them as different jobs rather than a swap. The Emtek 7107 is a passage function tubular lockset with no key, correct for interior doors that only need to latch, and it is specified as residential hardware. The Omnia D12036A is a single cylinder deadbolt lever lockset, so it adds a keyed bolt that most interior passage openings neither need nor are prepped for, and the door would need bolt prep it does not currently have. If the existing opening is a passage bore, stay with the 7107; if you are adding security to that door, plan on new prep for the Omnia.

Keep the function to the door. The Emtek 7107 covers the passage doors - hall, bedroom entries that only latch - in sandcast bronze with your choice of knob or lever trim and handing specified for lever versions. Where a door has to lock with a key, the Omnia D12036A gives you a single cylinder deadbolt lever lockset and the D12036AC the double cylinder equivalent with a sideplate design. Closet or false pairs take the Omnia D12036PD double dummy with plates at 5-1/2 inch center to center. Note the Emtek is bronze and the Omnia sets are solid brass, so finish matching across the two brands should be confirmed against samples.