Pass & Seymour Flexcor FC0 Ser...
IN STOCK (leaves warehouse same day if ordered before 3pm ET)
$50.23
Pass & Seymour Flexcor FC0 Series Standard Duty Closed Mesh Single-Eye Support Grip

Pass & Seymour Flexcor FC0 Series Standard Duty Closed Mesh Single-Eye Support Grip

(No reviews yet) Write a Review

Model: FC050-U

In Stock (leaves warehouse same day if ordered before 3pm ET)

$50.23
Adding to cart… The item has been added
Free Shipping on orders over $199
We price match and offer bulk discounts! Click Add to Quote. It's quick and easy.
✨
Earn points with this purchase! You can redeem points for giftcards, iPads, XBox's and more. View Rewards
Free Keying on all locks
You may also like

Pass & Seymour Flexcor FC0 Series Standard Duty Closed Mesh Single-Eye Support Grip

The Pass & Seymour Flexcor FC0 Series Standard Duty Closed Mesh Single-Eye Support Grip is engineered to support electrical and fiber optic cable, metal rods, and tubing on vertical runs. This closed mesh, single-eye configuration is woven of corrosion-resistant tinned-stainless steel wire and is available in a range of cable diameters from 0.50" - 0.99" to fit a variety of vertical support applications. Standard duty grips in this family are rated for loads up to 600 lbs and vertical runs of no more than 100 ft, and the line carries CSA Listing, making it a dependable choice for professional electrical and communications installations where the end of the cable is accessible for installation.

Key Features

  • Cable Diameter Range: Available in cable diameters from 0.50" - 0.99" for secure, properly fitted support across multiple cable sizes.
  • Durable Construction: Woven of corrosion-resistant tinned-stainless steel wire for long service life in demanding indoor and outdoor environments.
  • Closed Mesh, Single-Eye Grip: Closed mesh design is intended for applications where the end of the cable is accessible, terminating in a single-eye grip for straightforward rigging and attachment.
  • Bale Length: 8-in bale length for secure connection to the support point.
  • Mesh Length: 14-in mesh length provides ample wire-mesh contact along the supported cable.
  • Load Rating: Standard duty closed mesh support grips are designed for loads up to 600 lbs.
  • Vertical Run Limit: Suitable for vertical runs of no more than 100 ft.
  • Application Range: Available in a variety of eye styles and cable ranges for supporting electrical and fiber optic cable, metal rods, and tubing.

Certifications & Compliance

  • CSA Listed

Technical Specifications

  • Cable Diameter Range: 0.50" - 0.99"
  • Country of Origin: Mexico
  • Packaging: 10 EA per package

Typical Applications

  • Electrical and Fiber Optic Cable Support
  • Vertical Cable Runs in Commercial and Industrial Installations
  • Metal Rod and Tubing Support
  • Cable Tray, Riser, and Vertical Shaft Installations
  • Renovation and New Construction Electrical Projects

Why Pass & Seymour?

Pass & Seymour builds the Flexcor FC0 Series from corrosion-resistant tinned-stainless steel wire and backs it with CSA Listing, giving electrical and communications professionals a reliable, code-compliant support grip for cable, rod, and tubing across a range of cable diameters in demanding vertical run applications where dependable, long-term performance is required.

Manufacturer Resources

Spec Sheet

Product Specs

list_batch:
PASS-20260820
Product Type:
Support Grip
Configuration:
Closed Mesh Single-Eye
Series:
FC0 Series
Listing:
CSA Listed
Product Material:
Tinned-Stainless Steel
Product Size:
0.75" - 0.99"
Department:
Electrical
Product Group:
Hangers, Supports & Fasteners
Product Subgroup:
Cable Support Systems

Pass & Seymour FC050-U – Frequently Asked Questions

1) How do I pick the right size Pass & Seymour FC0 support grip for my cable OD?
Measure the actual outside diameter of the cable jacket and match it to one of the three FC0 ranges: 0.50 to 0.61 inch (FC050-U), 0.62 to 0.74 inch (FC062-U), and 0.75 to 0.99 inch (FC075-U). The mesh has to close down on the jacket to grip, so a grip sized above your cable OD will slip and one sized below will not slide on. If your cable falls on a boundary, go with the range that contains the measured OD, not the nominal cable size.
2) Can a closed mesh grip be installed on a cable that's already terminated at both ends?
No. The FC0 closed mesh grip slides on over the end of the cable, so the cable end has to be accessible and free. If both ends are already terminated or pulled through, you need a split-mesh or lace-up style grip that wraps around the cable mid-run instead.
3) Will a stainless mesh cable grip hold up in an outdoor or damp riser?
The FC0 mesh is woven from corrosion-resistant tinned-stainless steel wire, which is why it is spec'd for both indoor and outdoor service. That matters in a wet riser, a parking structure, or a coastal install where plain galvanized mesh would start showing rust at the weave points.
4) How much room do I need above the cable to rig an FC0 grip?
Allow for the 8-inch bale plus the 14-inch mesh body, so roughly two feet of cable length from your attachment point down. The single eye bale goes over a hook, shackle, or threaded support, and the 14 inches of mesh is what grips the jacket. Tight shaft tops and low beam clearances are where installers get caught.
5) Is the Pass & Seymour FC0 grip approved for electrical work in Canada?
The Flexcor FC0 line carries CSA Listing, so it is acceptable for professional electrical and communications installs on jobs that call for CSA-listed support hardware.
6) Can I use a Flexcor FC0 mesh grip to support conduit, tubing, or metal rod instead of cable?
Yes. Besides electrical and fiber optic cable, the FC0 grips are used to support metal rods and tubing on vertical runs. The sizing rule is the same, match the outside diameter of the rod or tube to one of the three ranges between 0.50 and 0.99 inch.
7) Do FC0 support grips come individually or in a box quantity?
They ship 10 each per package, which is worth knowing if you are stocking a riser job that needs several sizes. Order by MPN per range: FC050-U, FC062-U, or FC075-U.
8) What's the difference between a single-eye and a double-eye support grip?
Single eye, like the FC0 closed mesh grips, gives you one bale for a single attachment point, which is the normal arrangement for a straight vertical drop in a riser or shaft. Double eye versions exist in the wider Flexcor family and are used where the load gets split between two attachment points. For a standard vertical cable support off one hook or anchor, single eye is what you want.
How fast can I get the Pass & Seymour FC050-U delivered?
Most orders ship the same day from our distribution partners, with quick delivery throughout the continental U.S. Need it urgently? Contact Us for expedited shipping options.
Can I return it if it doesn’t work for me?
Yes—ZenSupply offers a hassle-free return policy. If the product isn’t the right fit, reach out to our support team for a return authorization or setup a return by following our return instructions.
Does the Pass & Seymour FC050-U come with a warranty?
Absolutely. The Pass & Seymour FC050-U is backed by a manufacturer’s warranty. For full warranty terms, check the product documentation or Contact Us.
How do I get technical support or installation help for the Pass & Seymour FC050-U?
You can call, text, or email our expert support team for fast answers. We’re here to help with product selection, installation tips, and troubleshooting. Contact Us
Why buy the Pass & Seymour FC050-U from ZenSupply?
ZenSupply makes it easy to get the commercial door hardware you need—fast shipping, expert support, and rewards on every order. Our team is always ready to help you choose the right product for your project.
!